config root man

# DEBUG_SYNC must be compiled in.
--source include/have_debug_sync.inc

--source include/have_innodb.inc

CREATE TABLE t1 (c1 INT , c2 CHAR(10), PRIMARY KEY (c1)) ENGINE = InnoDB;
INSERT INTO t1 VALUES(0, "0");
INSERT INTO t1 VALUES(1, "1");
INSERT INTO t1 VALUES(2, "2");
INSERT INTO t1 VALUES(3, "3");

--connect (con1,localhost,root,,)
--connect (con2,localhost,root,,)
--connect (con3,localhost,root,,)
--connect (con4,localhost,root,,)
--connect (con5,localhost,root,,)
--connect (con6,localhost,root,,)

connection default;
# Disable query log to avoid non-deterministic output conflicts
SET AUTOCOMMIT=0;
BEGIN;
# Lock all the records
SELECT * FROM t1 FOR UPDATE;
--disable_query_log

connection con1;
SET AUTOCOMMIT=1;
# Test if locking autocommit selects end up in the trx_sys_t::trx_list.
# We check this via the INFORMATION_SCHEMA.INNODB_TRX.
# This should block and show up in the I_S.
SET DEBUG_SYNC='lock_wait_suspend_thread_enter SIGNAL waiting1';
--send
SELECT COUNT(*) FROM t1 LOCK IN SHARE MODE;

connection con2;
SET AUTOCOMMIT=1;
# Test if non-locking autocommit selects end up in the trx_sys_t::trx_list.
# We check this via the INFORMATION_SCHEMA.INNODB_TRX.
# This should not block and should not show up in the I_S.
--send
SELECT COUNT(*) FROM t1;

connection con3;
SET AUTOCOMMIT=1;
# Note: autocommit non-locking selects are not converted to locking selects
# Therefore this should not block;
SET SESSION TRANSACTION ISOLATION LEVEL SERIALIZABLE;
--send
SELECT COUNT(*) FROM t1;

connection con4;
SET AUTOCOMMIT=0;
# Note: Non-locking selects are converted to locking selects
# therefore this should block;
SET SESSION TRANSACTION ISOLATION LEVEL SERIALIZABLE;
SET DEBUG_SYNC='now WAIT_FOR waiting1';
SET DEBUG_SYNC='lock_wait_suspend_thread_enter SIGNAL waiting4';
--send
SELECT COUNT(*) FROM t1 WHERE c1 >= 0;

connection con5;
SET AUTOCOMMIT=1;
# This should not block
BEGIN;
--send
SELECT COUNT(*) FROM t1;

connection con6;
SET AUTOCOMMIT=1;
# This will ignore the auto-commit setting but wont block because it is
# a non-locking select.
XA START '1';
--enable_query_log
SELECT * FROM t1 WHERE c1 <= 3;

connection default;
# Wait for SELECTs to get into the lock wait queue
SET DEBUG_SYNC='now WAIT_FOR waiting4';

# Check the number of non-locking transactions
let $wait_condition =
 SELECT COUNT(*) = 5
 FROM INFORMATION_SCHEMA.INNODB_TRX
 WHERE trx_autocommit_non_locking = 0;
--source include/wait_condition.inc

# Check the waiting transactions
SELECT trx_state, trx_query, trx_autocommit_non_locking
FROM INFORMATION_SCHEMA.INNODB_TRX
WHERE trx_state = 'LOCK WAIT'
ORDER BY trx_query;

INSERT INTO t1 VALUES(4, '4');
COMMIT;

connection con6;
SELECT * FROM t1 WHERE c1 <= 4;
XA END '1';
XA PREPARE '1';
XA ROLLBACK '1';

connection default;
disconnect con2;
disconnect con3;
disconnect con5;
disconnect con6;

connection con1;
reap;
disconnect con1;

connection con4;
reap;
disconnect con4;

connection default;
DROP TABLE t1;

# Clean up resources used in this test case.
--disable_warnings
SET DEBUG_SYNC= 'RESET';
--enable_warnings