| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/drm/radeon/@/dev/en/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/drm/radeon/@/dev/en/midwayreg.h |
/* $NetBSD: midwayreg.h,v 1.6 1997/03/20 21:34:47 chuck Exp $ */ /* * m i d w a y r e g . h * * this file contains the description of the ENI ATM midway chip * data structures. see midway.c for more details. * * $FreeBSD: release/9.1.0/sys/dev/en/midwayreg.h 114018 2003-04-25 16:14:03Z harti $ */ #define MID_SZTOB(X) ((X) * 256 * 4) /* size to bytes */ #define MID_BTOSZ(X) ((X) / 256 / 4) /* bytes to "size" */ #define MID_N_VC 1024 /* # of VCs we can use */ #define MID_VCI_BITS 10 /* number of bits */ #define MID_NTX_CH 8 /* 8 transmit channels (shared) */ #define MID_ATMDATASZ 48 /* need data in 48 byte blocks */ /* * card data structures, top down * * in order to have a portable driver, the netbsd guys will not let us * use structs. we have a bus_space_handle_t which is the en_base address. * everything else is an offset from that base. all card data must be * accessed with bus_space_read_4()/bus_space_write_4(): * * rv = bus_space_read_4(sc->en_memt, sc->en_base, BYTE_OFFSET); * bus_space_write_4(sc->en_memt, sc->en_base, BYTE_OFFSET, VALUE); * * en_card: the whole card (prom + phy + midway + obmem) * obmem contains: vci tab + dma queues (rx & tx) + service list + bufs */ /* byte offsets from en_base of various items */ #define MID_SUNIOFF 0x020000 /* SUNI offset */ #define MID_PHYOFF 0x030000 /* PHY offset */ #define MID_MIDOFF 0x040000 /* midway regs offset */ #define MID_RAMOFF 0x200000 /* RAM offset */ #define MID_DRQOFF 0x204000 /* DRQ offset */ #define MID_DRQEND MID_DTQOFF /* DRQ end */ #define MID_DTQOFF 0x205000 /* DTQ offset */ #define MID_DTQEND MID_SLOFF /* DTQ end */ #define MID_SLOFF 0x206000 /* service list */ #define MID_SLEND MID_BUFOFF /* service list end */ #define MID_BUFOFF 0x207000 /* buffer area */ #define MID_PROBEOFF 0x21fffc /* start probe here */ #define MID_PROBSIZE 0x020000 /* 128 KB */ #define MID_MAXOFF 0x3ffffc /* max offset */ /* * prom & phy: not defined here */ #define MID_ADPMACOFF 0xffc0 /* mac address offset (adaptec only) */ #define MID_NSUNI 256 /* suni registers */ /* * midway regs (byte offsets from en_base) */ #define MID_RESID 0x40000 /* write=reset reg, read=ID reg */ #define MID_VER(X) (((X) & 0xf0000000) >> 28) /* midway version # */ #define MID_MID(X) (((X) & 0x700) >> 8) /* motherboard ID */ #define MID_IS_SABRE(X) ((X) & 0x80) /* sabre controller? */ #define MID_IS_SUNI(X) ((X) & 0x40) /* SUNI? vs utopia */ #define MID_IS_UPIPE(X) ((X) & 0x20) /* utopia pipeline? */ #define MID_DID(X) ((X) & 0x1f) /* daughterboard ID */ #define MID_INTACK 0x40004 /* interrupt ACK */ #define MID_INTSTAT 0x40008 /* interrupt status */ #define MID_INTENA 0x4000c /* interrupt enable */ #define MID_TXCHAN(N) (1 << ((N) + 9)) /* ack/status/enable xmit channel bit*/ #define MID_INT_TX 0x1fe00 /* mask for any xmit interrupt */ #define MID_INT_DMA_OVR 0x00100 /* DMA overflow interrupt */ #define MID_INT_IDENT 0x00080 /* ident match error interrupt */ #define MID_INT_LERR 0x00040 /* LERR interrupt (sbus?) */ #define MID_INT_DMA_ERR 0x00020 /* DMA error interrupt */ #define MID_INT_DMA_RX 0x00010 /* DMA recv interrupt */ #define MID_INT_DMA_TX 0x00008 /* DMA xmit interrupt */ #define MID_INT_SERVICE 0x00004 /* service list interrupt */ #define MID_INT_SUNI 0x00002 /* SUNI interrupt */ #define MID_INT_STATS 0x00001 /* stats overflow interrupt */ #define MID_INT_ANY 0x1ffff /* any interrupt? */ #define MID_INTBITS "\20\21T7\20T6\17T5\16T4\15T3\14T2\13T1\12T0\11DMAOVR\10ID\7LERR\6DMAERR\5RXDMA\4TXDMA\3SERV\2SUNI\1STAT" #define MID_MAST_CSR 0x40010 /* master CSR */ #define MID_IPL(X) (((X) & 0x1c0) >> 6) /* IPL */ #define MID_SETIPL(I) ((I) << 6) #define MID_MCSR_TXLOCK 0x20 /* lock on xmit overflow mode */ /* NOTE: next 5 bits: write 1 means enable, write 0 means no change */ #define MID_MCSR_ENDMA 0x10 /* DMA enable */ #define MID_MCSR_ENTX 0x08 /* TX enable */ #define MID_MCSR_ENRX 0x04 /* RX enable */ #define MID_MCSR_W1MS 0x02 /* wait 1 msec */ #define MID_MCSR_W500US 0x01 /* wait 500 usec */ #define MID_MCSRBITS "\20\6LCK\5DMAON\4TXON\3RXON\2W1MS\1W500US" #define MID_STAT 0x40014 /* stat register, clear on read */ #define MID_VTRASH(X) (((X) >> 16) & 0xffff) /* # cells trashed due to VCI's mode */ #define MID_OTRASH(X) ((X) & 0xffff) /* # cells trashed due to overflow */ #define MID_SERV_WRITE 0x40018 /* 10 bit service write pointer (r/o) */ #define MID_DMA_ADDR 0x4001c /* VA of DMA (r/o) */ /* DMA queue pointers (bits 0 to 8) */ #define MID_DMA_WRRX 0x40020 /* write ptr. for DMA recv queue */ /* (for adaptor -> host xfers) */ #define MID_DMA_RDRX 0x40024 /* read ptr for DMA recv queue (r/o) */ /* (i.e. current adaptor->host xfer) */ #define MID_DMA_WRTX 0x40028 /* write ptr for DMA xmit queue */ /* (for host -> adaptor xfers) */ #define MID_DMA_RDTX 0x4002c /* read ptr for DMA xmit queue (r/o) */ /* (i.e. current host->adaptor xfer) */ /* xmit channel regs (1 per channel, MID_NTX_CH max channels) */ #define MIDX_PLACE(N) (0x40040+((N)*0x10)) /* xmit place */ #define MIDX_MKPLACE(SZ,LOC) ( ((SZ) << 11) | (LOC) ) #define MIDX_LOC(X) ((X) & 0x7ff) /* location in obmem */ #define MIDX_SZ(X) ((X) >> 11) /* (size of block / 256) in int32_t's*/ #define MIDX_BASE(X) \ (((MIDX_LOC(X) << MIDV_LOCTOPSHFT) * sizeof(uint32_t)) + MID_RAMOFF) /* the following two regs are word offsets in the block */ /* xmit read pointer (r/o) */ #define MIDX_READPTR(N) (0x40044 + ((N) * 0x10)) /* seg currently in DMA (r/o) */ #define MIDX_DESCSTART(N) (0x40048 + ((N) * 0x10)) /* * obmem items */ /* * vci table in obmem (offset from MID_VCTOFF) */ #define MID_VC(N) (MID_RAMOFF + ((N) * 0x10)) #define MIDV_TRASH 0x00000000 /* ignore VC */ #define MIDV_AAL5 0x80000000 /* do AAL5 on it */ #define MIDV_NOAAL 0x40000000 /* do per-cell stuff on it */ #define MIDV_MASK 0xc0000000 /* mode mask */ #define MIDV_SETMODE(VC,M) (((VC) & ~(MIDV_MASK)) | (M)) /* new mode */ #define MIDV_PTI 0x20000000 /* save PTI cells? */ #define MIDV_LOCTOPSHFT 8 /* shift to get top 11 bits of 19 */ #define MIDV_LOCSHIFT 18 #define MIDV_LOCMASK 0x7ff #define MIDV_LOC(X) (((X) >> MIDV_LOCSHIFT) & MIDV_LOCMASK) /* 11 most sig bits of addr */ #define MIDV_SZSHIFT 15 #define MIDV_SZ(X) (((X) >> MIDV_SZSHIFT) & 7) /* size encoded the usual way */ #define MIDV_INSERVICE 0x1 /* in service list */ #define MID_DST_RP(N) (MID_VC(N)|0x4) #define MIDV_DSTART_SHIFT 16 /* shift */ #define MIDV_DSTART(X) (((X) >> MIDV_DSTART_SHIFT) & 0x7fff) #define MIDV_READP_MASK 0x7fff /* valid bits, (shift = 0) */ #define MID_WP_ST_CNT(N) (MID_VC(N)|0x8) /* write pointer/state/count */ #define MIDV_WRITEP_MASK 0x7fff0000 /* mask for write ptr. */ #define MIDV_WRITEP_SHIFT 16 #define MIDV_ST_IDLE 0x0000 #define MIDV_ST_TRASH 0xc000 #define MIDV_ST_REASS 0x4000 #define MIDV_CCOUNT 0x7ff /* cell count */ #define MID_CRC(N) (MID_VC(N)|0xc) /* CRC */ /* * dma recv q. */ #define MID_DMA_END (1 << 5) /* for both tx and rx */ #define MID_DMA_CNT(X) (((X) >> 16) & 0xffff) #define MID_DMA_TXCHAN(X) (((X) >> 6) & 0x7) #define MID_DMA_RXVCI(X) (((X) >> 6) & 0x3ff) #define MID_DMA_TYPE(X) ((X) & 0xf) #define MID_DRQ_N 512 /* # of descriptors */ /* convert byte offset to reg value */ #define MID_DRQ_A2REG(N) (((N) - MID_DRQOFF) >> 3) /* and back */ #define MID_DRQ_REG2A(N) (((N) << 3) + MID_DRQOFF) /* note: format of word 1 of RXQ is different beween ENI and ADP cards */ #define MID_MK_RXQ_ENI(CNT, VC, END, TYPE) \ (((CNT) << 16) | ((VC) << 6) | (END) | (TYPE)) #define MID_MK_RXQ_ADP(CNT, VC, END, JK) \ (((CNT) << 12) | ((VC) << 2) | ((END) >> 4) | (((JK) != 0) ? 1 : 0)) /* * dma xmit q. */ #define MID_DTQ_N 512 /* # of descriptors */ /* convert byte offset to reg value */ #define MID_DTQ_A2REG(N) (((N) - MID_DTQOFF) >> 3) /* and back */ #define MID_DTQ_REG2A(N) (((N) << 3) + MID_DTQOFF) /* note: format of word 1 of TXQ is different beween ENI and ADP cards */ #define MID_MK_TXQ_ENI(CNT, CHN, END, TYPE) \ (((CNT) << 16) | ((CHN) << 6) | (END) | (TYPE)) #define MID_MK_TXQ_ADP(CNT, CHN, END, JK) \ (((CNT) << 12) | ((CHN) << 2) | ((END) >> 4) | (((JK) != 0) ? 1 : 0)) /* * dma types */ #define MIDDMA_JK 0x3 /* just kidding */ #define MIDDMA_BYTE 0x1 /* byte */ #define MIDDMA_2BYTE 0x2 /* 2 bytes */ #define MIDDMA_WORD 0x0 /* word */ #define MIDDMA_2WORD 0x7 /* 2 words */ #define MIDDMA_4WORD 0x4 /* 4 words */ #define MIDDMA_8WORD 0x5 /* 8 words */ #define MIDDMA_16WORD 0x6 /* 16 words!!! */ #define MIDDMA_2WMAYBE 0xf /* 2 words, maybe */ #define MIDDMA_4WMAYBE 0xc /* 4 words, maybe */ #define MIDDMA_8WMAYBE 0xd /* 8 words, maybe */ #define MIDDMA_16WMAYBE 0xe /* 16 words, maybe */ #define MIDDMA_MAYBE 0xc /* mask to detect WMAYBE dma code */ #define MIDDMA_MAXBURST (16 * sizeof(uint32_t)) /* largest burst */ /* * service list */ #define MID_SL_N 1024 /* max # entries on slist */ /* convert byte offset to reg value */ #define MID_SL_A2REG(N) (((N) - MID_SLOFF) >> 2) /* and back */ #define MID_SL_REG2A(N) (((N) << 2) + MID_SLOFF) /* * data in the buffer area of obmem */ /* * recv buffer desc. (1 uint32_t at start of buffer) */ #define MID_RBD_SIZE 4 /* RBD size */ #define MID_CHDR_SIZE 4 /* on aal0, cell header size */ #define MID_RBD_ID(X) ((X) & 0xfe000000) /* get ID */ #define MID_RBD_STDID 0x36000000 /* standard ID */ #define MID_RBD_CLP 0x01000000 /* CLP: cell loss priority */ #define MID_RBD_CE 0x00010000 /* CE: congestion experienced */ #define MID_RBD_T 0x00001000 /* T: trashed due to overflow */ #define MID_RBD_CRCERR 0x00000800 /* CRC error */ #define MID_RBD_CNT(X) ((X) & 0x7ff) /* cell count */ /* * xmit buffer desc. (2 uint32_t's at start of buffer) * (note we treat the PR & RATE as a single uint8_t) */ #define MID_TBD_SIZE 8 #define MID_TBD_MK1(AAL,PR_RATE,CNT) \ (MID_TBD_STDID | (AAL) | ((PR_RATE) << 19) | (CNT)) #define MID_TBD_STDID 0xb0000000 /* standard ID */ #define MID_TBD_AAL5 0x08000000 /* AAL 5 */ #define MID_TBD_NOAAL5 0x00000000 /* not AAL 5 */ #define MID_TBD_MK2(VCI,PTI,CLP) \ (((VCI) << 4) | ((PTI) << 1) | (CLP)) /* * aal5 pdu tail, last 2 words of last cell of AAL5 frame * (word 2 is CRC .. handled by hw) */ #define MID_PDU_SIZE 8 #define MID_PDU_MK1(UU, CPI, LEN) \ (((UU) << 24) | ((CPI) << 16) | (LEN)) #define MID_PDU_LEN(X) ((X) & 0xffff)