| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/ichwd/@/amd64/compile/hs32/modules/usr/src/sys/modules/usb/u3g/@/dev/esp/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/ichwd/@/amd64/compile/hs32/modules/usr/src/sys/modules/usb/u3g/@/dev/esp/ncr53c9xreg.h |
/* $NetBSD: ncr53c9xreg.h,v 1.16 2009/09/07 13:31:44 tsutsui Exp $ */ /*- * Copyright (c) 1994 Peter Galbavy. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Peter Galbavy. * 4. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ /* $FreeBSD: release/9.1.0/sys/dev/esp/ncr53c9xreg.h 230701 2012-01-29 00:47:11Z marius $ */ #ifndef _NCR53C9XREG_H_ #define _NCR53C9XREG_H_ /* * Register addresses, relative to some base address */ #define NCR_TCL 0x00 /* RW - Transfer Count Low */ #define NCR_TCM 0x01 /* RW - Transfer Count Mid */ #define NCR_TCH 0x0e /* RW - Transfer Count High */ /* NOT on 53C90 */ #define NCR_FIFO 0x02 /* RW - FIFO data */ #define NCR_CMD 0x03 /* RW - Command (2 deep) */ #define NCRCMD_DMA 0x80 /* DMA Bit */ #define NCRCMD_NOP 0x00 /* No Operation */ #define NCRCMD_FLUSH 0x01 /* Flush FIFO */ #define NCRCMD_RSTCHIP 0x02 /* Reset Chip */ #define NCRCMD_RSTSCSI 0x03 /* Reset SCSI Bus */ #define NCRCMD_RESEL 0x40 /* Reselect Sequence */ #define NCRCMD_SELNATN 0x41 /* Select without ATN */ #define NCRCMD_SELATN 0x42 /* Select with ATN */ #define NCRCMD_SELATNS 0x43 /* Select with ATN & Stop */ #define NCRCMD_ENSEL 0x44 /* Enable (Re)Selection */ #define NCRCMD_DISSEL 0x45 /* Disable (Re)Selection */ #define NCRCMD_SELATN3 0x46 /* Select with ATN3 */ #define NCRCMD_RESEL3 0x47 /* Reselect3 Sequence */ #define NCRCMD_SNDMSG 0x20 /* Send Message */ #define NCRCMD_SNDSTAT 0x21 /* Send Status */ #define NCRCMD_SNDDATA 0x22 /* Send Data */ #define NCRCMD_DISCSEQ 0x23 /* Disconnect Sequence */ #define NCRCMD_TERMSEQ 0x24 /* Terminate Sequence */ #define NCRCMD_TCCS 0x25 /* Target Command Comp Seq */ #define NCRCMD_DISC 0x27 /* Disconnect */ #define NCRCMD_RECMSG 0x28 /* Receive Message */ #define NCRCMD_RECCMD 0x29 /* Receive Command */ #define NCRCMD_RECDATA 0x2a /* Receive Data */ #define NCRCMD_RECCSEQ 0x2b /* Receive Command Sequence*/ #define NCRCMD_ABORT 0x04 /* Target Abort DMA */ #define NCRCMD_TRANS 0x10 /* Transfer Information */ #define NCRCMD_ICCS 0x11 /* Initiator Cmd Comp Seq */ #define NCRCMD_MSGOK 0x12 /* Message Accepted */ #define NCRCMD_TRPAD 0x18 /* Transfer Pad */ #define NCRCMD_SETATN 0x1a /* Set ATN */ #define NCRCMD_RSTATN 0x1b /* Reset ATN */ #define NCR_STAT 0x04 /* RO - Status */ #define NCRSTAT_INT 0x80 /* Interrupt */ #define NCRSTAT_GE 0x40 /* Gross Error */ #define NCRSTAT_PE 0x20 /* Parity Error */ #define NCRSTAT_TC 0x10 /* Terminal Count */ #define NCRSTAT_VGC 0x08 /* Valid Group Code */ #define NCRSTAT_PHASE 0x07 /* Phase bits */ #define NCR_SELID 0x04 /* WO - Select/Reselect Bus ID */ #define NCR_BUSID_HMEXC32 0x40 /* HME xfer counter is 32bit */ #define NCR_BUSID_HMEENCID 0x10 /* HME encode reselection ID */ #define NCR_INTR 0x05 /* RO - Interrupt */ #define NCRINTR_SBR 0x80 /* SCSI Bus Reset */ #define NCRINTR_ILL 0x40 /* Illegal Command */ #define NCRINTR_DIS 0x20 /* Disconnect */ #define NCRINTR_BS 0x10 /* Bus Service */ #define NCRINTR_FC 0x08 /* Function Complete */ #define NCRINTR_RESEL 0x04 /* Reselected */ #define NCRINTR_SELATN 0x02 /* Select with ATN */ #define NCRINTR_SEL 0x01 /* Selected */ #define NCR_TIMEOUT 0x05 /* WO - Select/Reselect Timeout */ #define NCR_STEP 0x06 /* RO - Sequence Step */ #define NCRSTEP_MASK 0x07 /* the last 3 bits */ #define NCRSTEP_DONE 0x04 /* command went out */ #define NCR_SYNCTP 0x06 /* WO - Synch Transfer Period */ /* Default 5 (53C9X) */ #define NCR_FFLAG 0x07 /* RO - FIFO Flags */ #define NCRFIFO_SS 0xe0 /* Sequence Step (Dup) */ #define NCRFIFO_FF 0x1f /* Bytes in FIFO */ #define NCR_SYNCOFF 0x07 /* WO - Synch Offset */ /* 0 = ASYNC */ /* 1 - 15 = SYNC bytes */ #define NCR_CFG1 0x08 /* RW - Configuration #1 */ #define NCRCFG1_SLOW 0x80 /* Slow Cable Mode */ #define NCRCFG1_SRR 0x40 /* SCSI Reset Rep Int Dis */ #define NCRCFG1_PTEST 0x20 /* Parity Test Mod */ #define NCRCFG1_PARENB 0x10 /* Enable Parity Check */ #define NCRCFG1_CTEST 0x08 /* Enable Chip Test */ #define NCRCFG1_BUSID 0x07 /* Bus ID */ #define NCR_CCF 0x09 /* WO - Clock Conversion Factor */ /* 0 = 35.01 - 40MHz */ /* NEVER SET TO 1 */ /* 2 = 10MHz */ /* 3 = 10.01 - 15MHz */ /* 4 = 15.01 - 20MHz */ /* 5 = 20.01 - 25MHz */ /* 6 = 25.01 - 30MHz */ /* 7 = 30.01 - 35MHz */ #define NCR_TEST 0x0a /* WO - Test (Chip Test Only) */ #define NCR_CFG2 0x0b /* RW - Configuration #2 */ #define NCRCFG2_RSVD 0xa0 /* reserved */ #define NCRCFG2_FE 0x40 /* Features Enable */ #define NCRCFG2_DREQ 0x10 /* DREQ High Impedance */ #define NCRCFG2_SCSI2 0x08 /* SCSI-2 Enable */ #define NCRCFG2_BPA 0x04 /* Target Bad Parity Abort */ #define NCRCFG2_RPE 0x02 /* Register Parity Error */ #define NCRCFG2_DPE 0x01 /* DMA Parity Error */ #define NCRCFG2_HMEFE 0x10 /* HME feature enable */ #define NCRCFG2_HME32 0x80 /* HME 32 extended */ /* Config #3 only on 53C9X */ #define NCR_CFG3 0x0c /* RW - Configuration #3 */ #define NCRCFG3_RSVD 0xe0 /* reserved */ #define NCRCFG3_IDM 0x10 /* ID Message Res Check */ #define NCRCFG3_QTE 0x08 /* Queue Tag Enable */ #define NCRCFG3_CDB 0x04 /* CDB 10-bytes OK */ #define NCRCFG3_FSCSI 0x02 /* Fast SCSI */ #define NCRCFG3_FCLK 0x01 /* Fast Clock (>25MHz) */ /* * For some unknown reason, the ESP406/FAS408 looks like every * other ncr53c9x, except for configuration #3 register. At any * rate, if you're dealing with these chips, you need to use these * defines instead. */ /* Config #3 different on ESP406/FAS408 */ #define NCR_ESPCFG3 0x0c /* RW - Configuration #3 */ #define NCRESPCFG3_IDM 0x80 /* ID Message Res Check */ #define NCRESPCFG3_QTE 0x40 /* Queue Tag Enable */ #define NCRESPCFG3_CDB 0x20 /* CDB 10-bytes OK */ #define NCRESPCFG3_FSCSI 0x10 /* Fast SCSI */ #define NCRESPCFG3_SRESB 0x08 /* Save Residual Byte */ #define NCRESPCFG3_FCLK 0x04 /* Fast Clock (>25MHz) */ #define NCRESPCFG3_ADMA 0x02 /* Alternate DMA Mode */ #define NCRESPCFG3_T8M 0x01 /* Threshold 8 Mode */ /* Config #3 also different on NCR53CF9x/FAS100A/FAS216/FAS236 */ #define NCR_F9XCFG3 0x0c /* RW - Configuration #3 */ #define NCRF9XCFG3_IDM 0x80 /* ID Message Res Check */ #define NCRF9XCFG3_QTE 0x40 /* Queue Tag Enable */ #define NCRF9XCFG3_CDB 0x20 /* CDB 10-bytes OK */ #define NCRF9XCFG3_FSCSI 0x10 /* Fast SCSI */ #define NCRF9XCFG3_FCLK 0x08 /* Fast Clock (>25MHz) */ #define NCRF9XCFG3_SRESB 0x04 /* Save Residual Byte */ #define NCRF9XCFG3_ADMA 0x02 /* Alternate DMA Mode */ #define NCRF9XCFG3_T8M 0x01 /* Threshold 8 Mode */ /* Config #3 on FAS366 */ #define NCRFASCFG3_OBAUTO 0x80 /* auto push odd-byte to DMA */ #define NCRFASCFG3_EWIDE 0x40 /* Enable Wide-SCSI */ #define NCRFASCFG3_IDBIT3 0x20 /* Bit 3 of HME SCSI-ID */ #define NCRFASCFG3_IDRESCHK 0x10 /* ID message checking */ #define NCRFASCFG3_QUENB 0x08 /* 3-byte msg support */ #define NCRFASCFG3_CDB10 0x04 /* group 2 scsi-2 support */ #define NCRFASCFG3_FASTSCSI 0x02 /* 10 MB/S fast scsi mode */ #define NCRFASCFG3_FASTCLK 0x01 /* fast clock mode */ /* Config #4 only on ESP406/FAS408 */ #define NCR_CFG4 0x0d /* RW - Configuration #4 */ #define NCRCFG4_CRS1 0x80 /* Select register set #1 */ #define NCRCFG4_RSVD 0x7b /* reserved */ #define NCRCFG4_ACTNEG 0x04 /* Active negation */ /* The following registers are only on the ESP406/FAS408. The documentation refers to them as "Control Register Set #1". These are the registers that are visible when bit 7 of register 0x0d is set. This bit is common to both register sets. */ #define NCR_JMP 0x00 /* RO - Jumper Sense Register */ #define NCRJMP_RSVD 0xc0 /* reserved */ #define NCRJMP_ROMSZ 0x20 /* ROM Size 1=16K, 0=32K */ #define NCRJMP_J4 0x10 /* Jumper #4 */ #define NCRJMP_J3 0x08 /* Jumper #3 */ #define NCRJMP_J2 0x04 /* Jumper #2 */ #define NCRJMP_J1 0x02 /* Jumper #1 */ #define NCRJMP_J0 0x01 /* Jumper #0 */ #define NCR_PIOFIFO 0x04 /* WO - PIO FIFO, 4 bytes deep */ #define NCR_PSTAT 0x08 /* RW - PIO Status Register */ #define NCRPSTAT_PERR 0x80 /* PIO Error */ #define NCRPSTAT_SIRQ 0x40 /* Active High of SCSI IRQ */ #define NCRPSTAT_ATAI 0x20 /* ATA IRQ */ #define NCRPSTAT_FEMPT 0x10 /* PIO FIFO Empty */ #define NCRPSTAT_F13 0x08 /* PIO FIFO 1/3 */ #define NCRPSTAT_F23 0x04 /* PIO FIFO 2/3 */ #define NCRPSTAT_FFULL 0x02 /* PIO FIFO Full */ #define NCRPSTAT_PIOM 0x01 /* PIO/DMA Mode */ #define NCR_PIOI 0x0b /* RW - PIO Interrupt Enable */ #define NCRPIOI_RSVD 0xe0 /* reserved */ #define NCRPIOI_EMPTY 0x10 /* IRQ When Empty */ #define NCRPIOI_13 0x08 /* IRQ When 1/3 */ #define NCRPIOI_23 0x04 /* IRQ When 2/3 */ #define NCRPIOI_FULL 0x02 /* IRQ When Full */ #define NCRPIOI_FINV 0x01 /* Flag Invert */ #define NCR_CFG5 0x0d /* RW - Configuration #5 */ #define NCRCFG5_CRS1 0x80 /* Select Register Set #1 */ #define NCRCFG5_SRAM 0x40 /* SRAM Memory Map */ #define NCRCFG5_AADDR 0x20 /* Auto Address */ #define NCRCFG5_PTRINC 0x10 /* Pointer Increment */ #define NCRCFG5_LOWPWR 0x08 /* Low Power Mode */ #define NCRCFG5_SINT 0x04 /* SCSI Interrupt Enable */ #define NCRCFG5_INTP 0x02 /* INT Polarity */ #define NCRCFG5_AINT 0x01 /* ATA Interrupt Enable */ #define NCR_SIGNTR 0x0e /* RO - Signature */ /* Am53c974 Config #3 */ #define NCR_AMDCFG3 0x0c /* RW - Configuration #3 */ #define NCRAMDCFG3_IDM 0x80 /* ID Message Res Check */ #define NCRAMDCFG3_QTE 0x40 /* Queue Tag Enable */ #define NCRAMDCFG3_CDB 0x20 /* CDB 10-bytes OK */ #define NCRAMDCFG3_FSCSI 0x10 /* Fast SCSI */ #define NCRAMDCFG3_FCLK 0x08 /* Fast Clock (40MHz) */ #define NCRAMDCFG3_RSVD 0x07 /* Reserved */ /* Am53c974 Config #4 */ #define NCR_AMDCFG4 0x0d /* RW - Configuration #4 */ #define NCRAMDCFG4_GE 0xc0 /* Glitch Eater */ #define NCRAMDCFG4_GE12NS 0x00 /* Signal window 12ns */ #define NCRAMDCFG4_GE25NS 0x80 /* Signal window 25ns */ #define NCRAMDCFG4_GE35NS 0x40 /* Signal window 35ns */ #define NCRAMDCFG4_GE0NS 0xc0 /* Signal window 0ns */ #define NCRAMDCFG4_PWD 0x20 /* Reduced power feature */ #define NCRAMDCFG4_RSVD 0x13 /* Reserved */ #define NCRAMDCFG4_RAE 0x08 /* Active neg. REQ/ACK */ #define NCRAMDCFG4_RADE 0x04 /* Active neg. REQ/ACK/DAT */ /* * FAS366 */ #define NCR_RCL NCR_TCH /* Recommand counter low */ #define NCR_RCH 0xf /* Recommand counter high */ #define NCR_UID NCR_RCL /* fas366 part-uniq id */ /* status register #2 definitions (read only) */ #define NCR_STAT2 NCR_CCF #define NCRFAS_STAT2_SEQCNT 0x01 /* Sequence counter bit 7-3 enabled */ #define NCRFAS_STAT2_FLATCHED 0x02 /* FIFO flags register latched */ #define NCRFAS_STAT2_CLATCHED 0x04 /* Xfer cntr & recommand ctr latched */ #define NCRFAS_STAT2_CACTIVE 0x08 /* Command register is active */ #define NCRFAS_STAT2_SCSI16 0x10 /* SCSI interface is wide */ #define NCRFAS_STAT2_ISHUTTLE 0x20 /* FIFO Top register contains 1 byte */ #define NCRFAS_STAT2_OSHUTTLE 0x40 /* next byte from FIFO is MSB */ #define NCRFAS_STAT2_EMPTY 0x80 /* FIFO is empty */ #endif /* _NCR53C9XREG_H_ */