| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/mlx/@/amd64/compile/hs32/modules/usr/src/sys/modules/geom/geom_label/@/dev/mii/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/mlx/@/amd64/compile/hs32/modules/usr/src/sys/modules/geom/geom_label/@/dev/mii/acphyreg.h |
/*- * Copyright (c) 2001 Semen Ustimenko (semenu@FreeBSD.org) * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $FreeBSD: release/9.1.0/sys/dev/mii/acphyreg.h 165986 2007-01-12 22:58:04Z marius $ */ #ifndef _DEV_MII_ACPHYREG_H_ #define _DEV_MII_ACPHYREG_H_ /* * Register definitions for the Altima Communications AC101 */ #define MII_ACPHY_POL 0x10 /* Polarity int level */ /* High byte is interrupt mask register */ #define MII_ACPHY_INT 0x11 /* Interrupt control/status */ #define AC_INT_ACOMP 0x0001 /* Autoneg complete */ #define AC_INT_REM_FLT 0x0002 /* Remote fault */ #define AC_INT_LINK_DOWN 0x0004 /* Link not OK */ #define AC_INT_LP_ACK 0x0008 /* FLP ack recved */ #define AC_INT_PD_FLT 0x0010 /* Parallel detect fault */ #define AC_INT_PAGE_RECV 0x0020 /* New page recved */ #define AC_INT_RX_ER 0x0040 /* RX_ER transitions high */ #define AC_INT_JAB 0x0080 /* Jabber detected */ #define MII_ACPHY_DIAG 0x12 /* Diagnostic */ #define AC_DIAG_RX_LOCK 0x0100 #define AC_DIAG_RX_PASS 0x0200 #define AC_DIAG_SPEED 0x0400 /* Aneg speed result */ #define AC_DIAG_DUPLEX 0x0800 /* Aneg duplex result */ #define MII_ACPHY_PWRLOOP 0x13 /* Power/Loopback */ #define MII_ACPHY_CBLMEAS 0x14 /* Cable meas. */ #define MII_ACPHY_MCTL 0x15 /* Mode control */ #define AC_MCTL_FX_SEL 0x0001 /* FX mode */ #define AC_MCTL_BYP_PCS 0x0002 /* Bypass PCS */ #define AC_MCTL_SCRMBL 0x0004 /* Data scrambling */ #define AC_MCTL_REM_LOOP 0x0008 /* Remote loopback */ #define AC_MCTL_DIS_WDT 0x0010 /* Disable watchdog timer */ #define AC_MCTL_DIS_REC 0x0020 /* Disable recv error counter */ #define AC_MCTL_REC_FULL 0x0040 /* Recv error counter full */ #define AC_MCTL_FRC_FEF 0x0080 /* Force Far End Fault Insert. */ #define AC_MCTL_DIS_FEF 0x0100 /* Disable FEF Insertion */ #define AC_MCTL_LED_SEL 0x0200 /* Compat LED config */ #define AC_MCTL_ALED_SEL 0x0400 /* ActLED RX&TX - RX only */ #define AC_MCTL_10BT_SEL 0x0800 /* Enable 7-wire interface */ #define AC_MCTL_DIS_JAB 0x1000 /* Disable jabber */ #define AC_MCTL_FRC_LINK 0x2000 /* Force TX link up */ #define AC_MCTL_DIS_NLP 0x4000 /* Disable NLP check */ #define MII_ACPHY_REC 0x18 /* Recv error counter */ #endif /* _DEV_MII_ACPHYREG_H_ */