| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/runfw/@/arm/econa/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/runfw/@/arm/econa/econa_reg.h |
/*- * Copyright (c) 2009 Yohanes Nugroho <yohanes@gmail.com> * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $FreeBSD: release/9.1.0/sys/arm/econa/econa_reg.h 201468 2010-01-04 03:35:45Z rpaulo $ */ #ifndef _ARM_ECONA_REG_H #define _ARM_ECONA_REG_H #define ECONA_SRAM_SIZE 0x10000000 #define ECONA_DRAM_BASE 0x00000000 /* DRAM (via DDR Control Module) */ #define ECONA_SDRAM_BASE 0x40000000 #define ECONA_SDRAM_SIZE 0x1000000 #define ECONA_IO_BASE 0x70000000 #define ECONA_IO_SIZE 0x0E000000 #define ECONA_PIC_BASE 0x0D000000 #define ECONA_PIC_SIZE 0x01000000 #define ECONA_UART_BASE 0x08000000 #define ECONA_UART_SIZE 0x01000000 #define ECONA_IRQ_UART 0xA #define ECONA_TIMER_BASE 0x09000000 #define ECONA_TIMER_SIZE 0x01000000 #define ECONA_IRQ_TIMER_1 0 #define ECONA_IRQ_TIMER_2 1 #define ECONA_IRQ_OHCI 23 #define ECONA_IRQ_EHCI 24 #define ECONA_NET_BASE 0x00000000 #define ECONA_SYSTEM_BASE 0x07000000 #define ECONA_SYSTEM_SIZE 0x01000000 #define ECONA_NET_SIZE 0x01000000 #define ECONA_CFI_PBASE 0x10000000 #define ECONA_CFI_VBASE 0xD0000000 #define ECONA_CFI_SIZE 0x10000000 #define ECONA_IRQ_STATUS 18 #define ECONA_IRQ_TSTC 19 #define ECONA_IRQ_FSRC 20 #define ECONA_IRQ_TSQE 21 #define ECONA_IRQ_FSQF 22 #define ECONA_IRQ_SYSTEM 0 #define ECONA_EHCI_PBASE 0xC8000000 #define ECONA_EHCI_VBASE 0xF8000000 #define ECONA_EHCI_SIZE 0x8000000 #define ECONA_OHCI_PBASE 0xC0000000 #define ECONA_OHCI_VBASE 0xF0000000 #define ECONA_OHCI_SIZE 0x8000000 #define ECONA_USB_SIZE 0xf000000 /*Interrupt controller*/ #define INTC_LEVEL_TRIGGER 0 #define INTC_EDGE_TRIGGER 1 #define INTC_ACTIVE_HIGH 0 #define INTC_ACTIVE_LOW 1 /* * define rising/falling edge for edge trigger mode */ #define INTC_RISING_EDGE 0 #define INTC_FALLING_EDGE 1 #define INTC_INTERRUPT_SOURCE_REG_OFFSET 0x00 #define INTC_INTERRUPT_MASK_REG_OFFSET 0x04 #define INTC_INTERRUPT_CLEAR_EDGE_TRIGGER_REG_OFFSET 0x08 #define INTC_INTERRUPT_TRIGGER_MODE_REG_OFFSET 0x0C #define INTC_INTERRUPT_TRIGGER_LEVEL_REG_OFFSET 0x10 #define INTC_INTERRUPT_STATUS_REG_OFFSET 0x14 #define INTC_FIQ_MODE_SELECT_REG_OFFSET 0x18 #define INTC_SOFTWARE_INTERRUPT_REG_OFFSET 0x1C /* * define rising/falling edge for edge trigger mode */ #define INTC_RISING_EDGE 0 #define INTC_FALLING_EDGE 1 #define TIMER_TM1_COUNTER_REG 0x00 #define TIMER_TM1_LOAD_REG 0x04 #define TIMER_TM1_MATCH1_REG 0x08 #define TIMER_TM1_MATCH2_REG 0x0C #define TIMER_TM2_COUNTER_REG 0x10 #define TIMER_TM2_LOAD_REG 0x14 #define TIMER_TM2_MATCH1_REG 0x18 #define TIMER_TM2_MATCH2_REG 0x1C #define TIMER_TM_CR_REG 0x30 #define TIMER_TM_INTR_STATUS_REG 0x34 #define TIMER_TM_INTR_MASK_REG 0x38 #define TIMER_TM_REVISION_REG 0x3C #define INTC_TIMER1_BIT_INDEX 0 #define TIMER1_UP_DOWN_COUNT (1<<9) #define TIMER2_UP_DOWN_COUNT (1<<10) #define TIMER1_MATCH1_INTR (1<<0) #define TIMER1_MATCH2_INTR (1<<1) #define TIMER1_OVERFLOW_INTR (1<<2) #define TIMER2_MATCH1_INTR (1<<3) #define TIMER2_MATCH2_INTR (1<<4) #define TIMER2_OVERFLOW_INTR (1<<5) #define TIMER_CLOCK_SOURCE_PCLK 0 #define TIMER_CLOCK_SOURCE_EXT_CLK 1 /* * define interrupt trigger mode */ #define INTC_LEVEL_TRIGGER 0 #define INTC_EDGE_TRIGGER 1 #define INTC_TRIGGER_UNKNOWN -1 #define TIMER1_OVERFLOW_INTERRUPT (1<<2) #define TIMER2_OVERFLOW_INTERRUPT (1<<5) #define TIMER_INTERRUPT_STATUS_REG 0x34 #define TIMER1_ENABLE (1<<0) #define TIMER1_CLOCK_SOURCE (1<<1) #define TIMER1_OVERFLOW_ENABLE (1<<2) #define TIMER2_ENABLE (1<<3) #define TIMER2_CLOCK_SOURCE (1<<4) #define TIMER2_OVERFLOW_ENABLE (1<<5) #define TIMER_1 1 #define EC_UART_CLOCK 14769200 #define EC_UART_REGSHIFT 2 #define SYSTEM_CLOCK 0x14 #define RESET_CONTROL 0x4 #define GLOBAL_RESET 0x1 #define NET_INTERFACE_RESET (0x1 << 4) #endif