Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/siftr/@/dev/aha/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/siftr/@/dev/aha/ahareg.h |
/*- * Generic register and struct definitions for the Adaptech 1540, 1542, * 1640, 1642 SCSI host adapters. Product specific probe and attach * routines can be found in: * aha_isa.c, aha_mca.c * * Derived from bt.c written by: * * Copyright (c) 1998 Justin T. Gibbs. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions, and the following disclaimer, * without modification, immediately at the beginning of the file. * 2. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $FreeBSD: release/9.1.0/sys/dev/aha/ahareg.h 164110 2006-11-09 02:19:30Z kevlo $ */ #ifndef _AHAREG_H_ #define _AHAREG_H_ #include <sys/queue.h> #include <cam/scsi/scsi_all.h> #define AHA_MAXTRANSFER_SIZE 0xffffff /* limited by 24bit counter */ #define AHA_NSEG 17 /* The number of dma segments * supported. */ #define ALL_TARGETS (~0) /* * Control Register pp. 1-8, 1-9 (Write Only) */ #define CONTROL_REG 0x00 #define HARD_RESET 0x80 /* Hard Reset - return to POST state */ #define SOFT_RESET 0x40 /* Soft Reset - Clears Adapter state */ #define RESET_INTR 0x20 /* Reset/Ack Interrupt */ #define RESET_SBUS 0x10 /* Drive SCSI bus reset signal */ /* * Status Register pp. 1-9, 1-10 (Read Only) */ #define STATUS_REG 0x00 #define DIAG_ACTIVE 0x80 /* Performing Internal Diags */ #define DIAG_FAIL 0x40 /* Internal Diags failed */ #define INIT_REQUIRED 0x20 /* MBOXes need initialization */ #define HA_READY 0x10 /* HA ready for new commands */ #define CMD_REG_BUSY 0x08 /* HA busy with last cmd byte */ #define DATAIN_REG_READY 0x04 /* Data-in Byte available */ #define STATUS_REG_RSVD 0x02 #define CMD_INVALID 0x01 /* Invalid Command detected */ /* * Command/Parameter Register pp. 1-10, 1-11 (Write Only) */ #define COMMAND_REG 0x01 /* * Data in Register p. 1-11 (Read Only) */ #define DATAIN_REG 0x01 /* * Interrupt Status Register pp. 1-12 -> 1-14 (Read Only) */ #define INTSTAT_REG 0x02 #define INTR_PENDING 0x80 /* There is a pending INTR */ #define INTSTAT_REG_RSVD 0x70 #define SCSI_BUS_RESET 0x08 /* Bus Reset detected */ #define CMD_COMPLETE 0x04 #define OMB_READY 0x02 /* Outgoin Mailbox Ready */ #define IMB_LOADED 0x01 /* Incoming Mailbox loaded */ /* * Definitions for the "undocumented" geometry register, we just need * its location. */ #define GEOMETRY_REG 0x03 #define AHA_NREGS (4) /* * Opcodes for Adapter commands. */ typedef enum { AOP_NOP = 0x00, AOP_INITIALIZE_MBOX = 0x01, AOP_START_MBOX = 0x02, AOP_EXECUTE_BIOS_CMD = 0x03, AOP_INQUIRE_BOARD_ID = 0x04, AOP_ENABLE_OMBR_INT = 0x05, AOP_SET_SEL_TIMOUT = 0x06, AOP_SET_TIME_ON_BUS = 0x07, AOP_SET_TIME_OFF_BUS = 0x08, AOP_SET_BUS_TRANS_RATE = 0x09, AOP_INQUIRE_INST_LDEVS = 0x0A, AOP_INQUIRE_CONFIG = 0x0B, AOP_ENABLE_TARGET_MODE = 0x0C, AOP_INQUIRE_SETUP_INFO = 0x0D, AOP_WRITE_LRAM = 0x1A, AOP_READ_LRAM = 0x1B, AOP_WRITE_CHIP_FIFO = 0x1C, AOP_READ_CHIP_FIFO = 0x1D, AOP_ECHO_DATA_BYTE = 0x1F, AOP_ADAPTER_DIAGNOSTICS = 0x20, AOP_SET_ADAPTER_OPTIONS = 0x21, AOP_SET_EEPROM = 0x22, AOP_RETURN_EEPROM = 0x23, AOP_ENABLE_SHADOW_RAM = 0x24, AOP_INIT_BIOS_MBOX = 0x25, AOP_SET_BIOS_BANK_1 = 0x26, AOP_SET_BIOS_BANK_2 = 0x27, AOP_RETURN_EXT_BIOS_INFO= 0x28, AOP_MBOX_IF_ENABLE = 0x29, AOP_SCSI_TERM_STATUS = 0x2C, AOP_INQUIRE_SCAM_DEV = 0x2D, AOP_SCSI_DEV_TABLE = 0x2E, AOP_SCAM_OP = 0x2F, AOP_START_BIOS_CMD = 0x82, AOP_INQUIRE_ESETUP_INFO = 0x8D } aha_op_t; /************** Definitions of Multi-byte commands and responses ************/ struct aha_extbios { uint8_t flags; /* Bit 3 == 1 extended bios enabled */ uint8_t mailboxlock; /* mail box lock code to unlock it */ }; typedef struct { uint8_t num_mboxes; uint8_t base_addr[3]; } init_24b_mbox_params_t; typedef struct { uint8_t board_type; /* These values are mostly from the aha-1540CP technical reference, but */ /* with other values from the old aha1542.c driver. The values from the */ /* aha-1540CP technical manual are used where conflicts arise */ #define BOARD_1540_16HEAD_BIOS 0x00 #define BOARD_1540_64HEAD_BIOS 0x30 #define BOARD_1542 0x41 /* aha-1540/1542 w/64-h bios */ #define BOARD_1640 0x42 /* aha-1640 */ #define BOARD_1740 0x43 /* aha-1740A/1742A/1744 */ #define BOARD_1542C 0x44 /* aha-1542C */ #define BOARD_1542CF 0x45 /* aha-1542CF */ #define BOARD_1542CP 0x46 /* aha-1542CP, plug and play */ uint8_t cust_features; #define FEATURES_STANDARD 0x30 uint8_t firmware_rev_major; uint8_t firmware_rev_minor; } board_id_data_t; typedef struct { uint8_t dma_chan; #define DMA_CHAN_5 0x20 #define DMA_CHAN_6 0x40 #define DMA_CHAN_7 0x80 uint8_t irq; #define IRQ_9 0x01 #define IRQ_10 0x02 #define IRQ_11 0x04 #define IRQ_12 0x08 #define IRQ_14 0x20 #define IRQ_15 0x40 uint8_t scsi_id; } config_data_t; typedef struct { uint8_t offset : 4, period : 3, sync : 1; } targ_syncinfo_t; typedef struct { uint8_t initiate_sync : 1, parity_enable : 1, : 6; uint8_t bus_transfer_rate; uint8_t time_on_bus; uint8_t time_off_bus; uint8_t num_mboxes; uint8_t mbox_base_addr[3]; targ_syncinfo_t syncinfo[8]; uint8_t discinfo; uint8_t customer_sig[20]; uint8_t auto_retry; uint8_t board_switches; uint8_t firmware_cksum[2]; uint8_t bios_mbox_addr[3]; } setup_data_t; #define AHA_NUM_ISAPORTS 6 typedef struct { uint8_t len[3]; uint8_t addr[3]; } aha_sg_t; /********************** Mail Box definitions *******************************/ typedef enum { AMBO_FREE = 0x0, /* MBO intry is free */ AMBO_START = 0x1, /* MBO activate entry */ AMBO_ABORT = 0x2 /* MBO abort entry */ } aha_mbo_action_code_t; typedef struct aha_mbox_out { uint8_t action_code; uint8_t ccb_addr[3]; } aha_mbox_out_t; typedef enum { AMBI_FREE = 0x0, /* MBI entry is free */ AMBI_OK = 0x1, /* completed without error */ AMBI_ABORT = 0x2, /* aborted ccb */ AMBI_NOT_FOUND = 0x3, /* Tried to abort invalid CCB */ AMBI_ERROR = 0x4 /* Completed with error */ } aha_mbi_comp_code_t; typedef struct aha_mbox_in { uint8_t comp_code; uint8_t ccb_addr[3]; } aha_mbox_in_t; /****************** Hardware CCB definition *********************************/ typedef enum { INITIATOR_CCB = 0x00, INITIATOR_SG_CCB = 0x02, INITIATOR_CCB_WRESID = 0x03, INITIATOR_SG_CCB_WRESID = 0x04, INITIATOR_BUS_DEV_RESET = 0x81 } aha_ccb_opcode_t; typedef enum { AHASTAT_NOERROR = 0x00, AHASTAT_SELTIMEOUT = 0x11, AHASTAT_DATARUN_ERROR = 0x12, AHASTAT_UNEXPECTED_BUSFREE = 0x13, AHASTAT_INVALID_PHASE = 0x14, AHASTAT_INVALID_ACTION_CODE = 0x15, AHASTAT_INVALID_OPCODE = 0x16, AHASTAT_LINKED_CCB_LUN_MISMATCH = 0x17, AHASTAT_INVALID_CCB_OR_SG_PARAM = 0x1A, AHASTAT_HA_SCSI_BUS_RESET = 0x22, /* stolen from bt */ AHASTAT_HA_BDR = 0x25 /* Stolen from bt */ } ahastat_t; struct aha_hccb { uint8_t opcode; /* 0 */ uint8_t lun : 3, /* 1 */ datain : 1, dataout : 1, target : 3; uint8_t cmd_len; /* 2 */ uint8_t sense_len; /* 3 */ uint8_t data_len[3]; /* 4 */ uint8_t data_addr[3]; /* 7 */ uint8_t link_ptr[3]; /* 10 */ uint8_t link_id; /* 13 */ uint8_t ahastat; /* 14 */ uint8_t sdstat; /* 15 */ uint8_t reserved1; /* 16 */ uint8_t reserved2; /* 17 */ uint8_t scsi_cdb[16]; /* 18 */ uint8_t sense_data[SSD_FULL_SIZE]; }; typedef enum { ACCB_FREE = 0x0, ACCB_ACTIVE = 0x1, ACCB_DEVICE_RESET = 0x2, ACCB_RELEASE_SIMQ = 0x4 } accb_flags_t; struct aha_ccb { struct aha_hccb hccb; /* hccb assumed to be at 0 */ SLIST_ENTRY(aha_ccb) links; uint32_t flags; union ccb *ccb; bus_dmamap_t dmamap; aha_sg_t *sg_list; uint32_t sg_list_phys; }; struct sg_map_node { bus_dmamap_t sg_dmamap; bus_addr_t sg_physaddr; aha_sg_t* sg_vaddr; SLIST_ENTRY(sg_map_node) links; }; struct aha_softc { bus_space_tag_t tag; bus_space_handle_t bsh; struct cam_sim *sim; struct cam_path *path; aha_mbox_out_t *cur_outbox; aha_mbox_in_t *cur_inbox; aha_mbox_out_t *last_outbox; aha_mbox_in_t *last_inbox; struct aha_ccb *aha_ccb_array; SLIST_HEAD(,aha_ccb) free_aha_ccbs; LIST_HEAD(,ccb_hdr) pending_ccbs; u_int active_ccbs; uint32_t aha_ccb_physbase; aha_ccb_opcode_t ccb_sg_opcode; aha_ccb_opcode_t ccb_ccb_opcode; aha_mbox_in_t *in_boxes; aha_mbox_out_t *out_boxes; struct scsi_sense_data *sense_buffers; uint32_t sense_buffers_physbase; struct aha_ccb *recovery_accb; u_int num_boxes; bus_dma_tag_t parent_dmat; /* * All dmat's derive from * the dmat defined by our * bus. */ bus_dma_tag_t buffer_dmat; /* dmat for buffer I/O */ bus_dma_tag_t mailbox_dmat; /* dmat for our mailboxes */ bus_dmamap_t mailbox_dmamap; bus_dma_tag_t ccb_dmat; /* dmat for our ccb array */ bus_dmamap_t ccb_dmamap; bus_dma_tag_t sg_dmat; /* dmat for our sg maps */ SLIST_HEAD(, sg_map_node) sg_maps; bus_addr_t mailbox_physbase; u_int num_ccbs; /* Number of CCBs malloc'd */ u_int max_ccbs; /* Maximum allocatable CCBs */ u_int max_sg; u_int unit; u_int scsi_id; uint32_t extended_trans :1, diff_bus :1, extended_lun :1, strict_rr :1, tag_capable :1, resource_shortage:1, :26; uint16_t disc_permitted; uint16_t sync_permitted; uint8_t init_level; volatile uint8_t command_cmp; volatile uint8_t latched_status; uint32_t bios_addr; uint8_t fw_major; uint8_t fw_minor; char model[32]; uint8_t boardid; struct resource *irq; struct resource *port; struct resource *drq; int irqrid; int portrid; int drqrid; void **ih; device_t dev; }; void aha_alloc(struct aha_softc *, int, bus_space_tag_t, bus_space_handle_t); int aha_attach(struct aha_softc *); int aha_cmd(struct aha_softc *, aha_op_t, uint8_t *, u_int, uint8_t *, u_int, u_int); int aha_detach(struct aha_softc *); int aha_fetch_adapter_info(struct aha_softc *); void aha_find_probe_range(int, int *, int *); void aha_free(struct aha_softc *); int aha_init(struct aha_softc *); void aha_intr(void *); int aha_probe(struct aha_softc *); #define DEFAULT_CMD_TIMEOUT 10000 /* 1 sec */ #define aha_inb(aha, port) \ bus_space_read_1((aha)->tag, (aha)->bsh, port) #define aha_outb(aha, port, value) \ bus_space_write_1((aha)->tag, (aha)->bsh, port, value) #define ADP0100_PNP 0x00019004 /* ADP0100 */ #define AHA1540_PNP 0x40159004 /* ADP1540 */ #define AHA1542_PNP 0x42159004 /* ADP1542 */ #define AHA1542_PNPCOMPAT 0xA000D040 /* PNP00A0 */ #define ICU0091_PNP 0X91005AA4 /* ICU0091 */ #endif /* _AHAREG_H_ */