| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/usb/urtw/@/amd64/compile/hs32/modules/usr/src/sys/modules/netgraph/ip_input/@/amd64/compile/hs32/modules/usr/src/sys/modules/usb/uslcom/@/amd64/compile/hs32/modules/usr/src/sys/modules/netgraph/ether/@/contrib/octeon-sdk/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/usb/urtw/@/amd64/compile/hs32/modules/usr/src/sys/modules/netgraph/ip_input/@/amd64/compile/hs32/modules/usr/src/sys/modules/usb/uslcom/@/amd64/compile/hs32/modules/usr/src/sys/modules/netgraph/ether/@/contrib/octeon-sdk/cvmx-wqe.h |
/***********************license start***************
* Copyright (c) 2003-2010 Cavium Networks (support@cavium.com). All rights
* reserved.
*
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
*
* * Redistributions in binary form must reproduce the above
* copyright notice, this list of conditions and the following
* disclaimer in the documentation and/or other materials provided
* with the distribution.
* * Neither the name of Cavium Networks nor the names of
* its contributors may be used to endorse or promote products
* derived from this software without specific prior written
* permission.
* This Software, including technical data, may be subject to U.S. export control
* laws, including the U.S. Export Administration Act and its associated
* regulations, and may be subject to export or import regulations in other
* countries.
* TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS"
* AND WITH ALL FAULTS AND CAVIUM NETWORKS MAKES NO PROMISES, REPRESENTATIONS OR
* WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH RESPECT TO
* THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY REPRESENTATION OR
* DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT DEFECTS, AND CAVIUM
* SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES OF TITLE,
* MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE, LACK OF
* VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET POSSESSION OR
* CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK ARISING OUT OF USE OR
* PERFORMANCE OF THE SOFTWARE LIES WITH YOU.
***********************license end**************************************/
/**
* @file
*
* This header file defines the work queue entry (wqe) data structure.
* Since this is a commonly used structure that depends on structures
* from several hardware blocks, those definitions have been placed
* in this file to create a single point of definition of the wqe
* format.
* Data structures are still named according to the block that they
* relate to.
*
* This file must not depend on any other header files, except for cvmx.h!!!
*
*
* <hr>$Revision: 49448 $<hr>
*
*
*/
#ifndef __CVMX_WQE_H__
#define __CVMX_WQE_H__
#ifdef __cplusplus
extern "C" {
#endif
#define OCT_TAG_TYPE_STRING(x) (((x) == CVMX_POW_TAG_TYPE_ORDERED) ? "ORDERED" : \
(((x) == CVMX_POW_TAG_TYPE_ATOMIC) ? "ATOMIC" : \
(((x) == CVMX_POW_TAG_TYPE_NULL) ? "NULL" : \
"NULL_NULL")))
/**
* HW decode / err_code in work queue entry
*/
typedef union
{
uint64_t u64;
/** Use this struct if the hardware determines that the packet is IP */
struct
{
uint64_t bufs : 8; /**< HW sets this to the number of buffers used by this packet */
uint64_t ip_offset : 8; /**< HW sets to the number of L2 bytes prior to the IP */
uint64_t vlan_valid : 1; /**< set to 1 if we found DSA/VLAN in the L2 */
uint64_t vlan_stacked : 1; /**< Set to 1 if the DSA/VLAN tag is stacked */
uint64_t unassigned : 1;
uint64_t vlan_cfi : 1; /**< HW sets to the DSA/VLAN CFI flag (valid when vlan_valid) */
uint64_t vlan_id :12; /**< HW sets to the DSA/VLAN_ID field (valid when vlan_valid) */
uint64_t pr : 4; /**< Ring Identifier (if PCIe). Requires PIP_GBL_CTL[RING_EN]=1 */
uint64_t unassigned2 : 8;
uint64_t dec_ipcomp : 1; /**< the packet needs to be decompressed */
uint64_t tcp_or_udp : 1; /**< the packet is either TCP or UDP */
uint64_t dec_ipsec : 1; /**< the packet needs to be decrypted (ESP or AH) */
uint64_t is_v6 : 1; /**< the packet is IPv6 */
/* (rcv_error, not_IP, IP_exc, is_frag, L4_error, software, etc.) */
uint64_t software : 1; /**< reserved for software use, hardware will clear on packet creation */
/* exceptional conditions below */
uint64_t L4_error : 1; /**< the receive interface hardware detected an L4 error (only applies if !is_frag)
(only applies if !rcv_error && !not_IP && !IP_exc && !is_frag)
failure indicated in err_code below, decode:
- 1 = Malformed L4
- 2 = L4 Checksum Error: the L4 checksum value is
- 3 = UDP Length Error: The UDP length field would make the UDP data longer than what
remains in the IP packet (as defined by the IP header length field).
- 4 = Bad L4 Port: either the source or destination TCP/UDP port is 0.
- 8 = TCP FIN Only: the packet is TCP and only the FIN flag set.
- 9 = TCP No Flags: the packet is TCP and no flags are set.
- 10 = TCP FIN RST: the packet is TCP and both FIN and RST are set.
- 11 = TCP SYN URG: the packet is TCP and both SYN and URG are set.
- 12 = TCP SYN RST: the packet is TCP and both SYN and RST are set.
- 13 = TCP SYN FIN: the packet is TCP and both SYN and FIN are set. */
uint64_t is_frag : 1; /**< set if the packet is a fragment */
uint64_t IP_exc : 1; /**< the receive interface hardware detected an IP error / exception
(only applies if !rcv_error && !not_IP) failure indicated in err_code below, decode:
- 1 = Not IP: the IP version field is neither 4 nor 6.
- 2 = IPv4 Header Checksum Error: the IPv4 header has a checksum violation.
- 3 = IP Malformed Header: the packet is not long enough to contain the IP header.
- 4 = IP Malformed: the packet is not long enough to contain the bytes indicated by the IP
header. Pad is allowed.
- 5 = IP TTL Hop: the IPv4 TTL field or the IPv6 Hop Count field are zero.
- 6 = IP Options */
uint64_t is_bcast : 1; /**< set if the hardware determined that the packet is a broadcast */
uint64_t is_mcast : 1; /**< set if the hardware determined that the packet is a multi-cast */
uint64_t not_IP : 1; /**< set if the packet may not be IP (must be zero in this case) */
uint64_t rcv_error : 1; /**< the receive interface hardware detected a receive error (must be zero in this case) */
/* lower err_code = first-level descriptor of the work */
/* zero for packet submitted by hardware that isn't on the slow path */
uint64_t err_code : 8; /**< type is cvmx_pip_err_t */
} s;
/**< use this to get at the 16 vlan bits */
struct
{
uint64_t unused1 :16;
uint64_t vlan :16;
uint64_t unused2 :32;
} svlan;
/**< use this struct if the hardware could not determine that the packet is ip */
struct
{
uint64_t bufs : 8; /**< HW sets this to the number of buffers used by this packet */
uint64_t unused : 8;
uint64_t vlan_valid : 1; /**< set to 1 if we found DSA/VLAN in the L2 */
uint64_t vlan_stacked : 1; /**< Set to 1 if the DSA/VLAN tag is stacked */
uint64_t unassigned : 1;
uint64_t vlan_cfi : 1; /**< HW sets to the DSA/VLAN CFI flag (valid when vlan_valid) */
uint64_t vlan_id :12; /**< HW sets to the DSA/VLAN_ID field (valid when vlan_valid) */
uint64_t pr : 4; /**< Ring Identifier (if PCIe). Requires PIP_GBL_CTL[RING_EN]=1 */
uint64_t unassigned2 :12;
uint64_t software : 1; /**< reserved for software use, hardware will clear on packet creation */
uint64_t unassigned3 : 1;
uint64_t is_rarp : 1; /**< set if the hardware determined that the packet is rarp */
uint64_t is_arp : 1; /**< set if the hardware determined that the packet is arp */
uint64_t is_bcast : 1; /**< set if the hardware determined that the packet is a broadcast */
uint64_t is_mcast : 1; /**< set if the hardware determined that the packet is a multi-cast */
uint64_t not_IP : 1; /**< set if the packet may not be IP (must be one in this case) */
uint64_t rcv_error : 1; /**< the receive interface hardware detected a receive error.
Failure indicated in err_code below, decode:
- 1 = partial error: a packet was partially received, but internal
buffering / bandwidth was not adequate to receive the entire packet.
- 2 = jabber error: the RGMII packet was too large and is truncated.
- 3 = overrun error: the RGMII packet is longer than allowed and had
an FCS error.
- 4 = oversize error: the RGMII packet is longer than allowed.
- 5 = alignment error: the RGMII packet is not an integer number of bytes
and had an FCS error (100M and 10M only).
- 6 = fragment error: the RGMII packet is shorter than allowed and had an
FCS error.
- 7 = GMX FCS error: the RGMII packet had an FCS error.
- 8 = undersize error: the RGMII packet is shorter than allowed.
- 9 = extend error: the RGMII packet had an extend error.
- 10 = length mismatch error: the RGMII packet had a length that did not
match the length field in the L2 HDR.
- 11 = RGMII RX error/SPI4 DIP4 Error: the RGMII packet had one or more
data reception errors (RXERR) or the SPI4 packet had one or more DIP4
errors.
- 12 = RGMII skip error/SPI4 Abort Error: the RGMII packet was not large
enough to cover the skipped bytes or the SPI4 packet was terminated
with an About EOPS.
- 13 = RGMII nibble error/SPI4 Port NXA Error: the RGMII packet had a
studder error (data not repeated - 10/100M only) or the SPI4 packet
was sent to an NXA.
- 16 = FCS error: a SPI4.2 packet had an FCS error.
- 17 = Skip error: a packet was not large enough to cover the skipped bytes.
- 18 = L2 header malformed: the packet is not long enough to contain the L2 */
/* lower err_code = first-level descriptor of the work */
/* zero for packet submitted by hardware that isn't on the slow path */
uint64_t err_code : 8; /* type is cvmx_pip_err_t (union, so can't use directly */
} snoip;
} cvmx_pip_wqe_word2;
/**
* Work queue entry format
*
* must be 8-byte aligned
*/
typedef struct
{
/*****************************************************************
* WORD 0
* HW WRITE: the following 64 bits are filled by HW when a packet arrives
*/
/**
* raw chksum result generated by the HW
*/
uint16_t hw_chksum;
/**
* Field unused by hardware - available for software
*/
uint8_t unused;
/**
* Next pointer used by hardware for list maintenance.
* May be written/read by HW before the work queue
* entry is scheduled to a PP
* (Only 36 bits used in Octeon 1)
*/
uint64_t next_ptr : 40;
/*****************************************************************
* WORD 1
* HW WRITE: the following 64 bits are filled by HW when a packet arrives
*/
/**
* HW sets to the total number of bytes in the packet
*/
uint64_t len :16;
/**
* HW sets this to input physical port
*/
uint64_t ipprt : 6;
/**
* HW sets this to what it thought the priority of the input packet was
*/
uint64_t qos : 3;
/**
* the group that the work queue entry will be scheduled to
*/
uint64_t grp : 4;
/**
* the type of the tag (ORDERED, ATOMIC, NULL)
*/
cvmx_pow_tag_type_t tag_type : 3;
/**
* the synchronization/ordering tag
*/
uint64_t tag :32;
/**
* WORD 2
* HW WRITE: the following 64-bits are filled in by hardware when a packet arrives
* This indicates a variety of status and error conditions.
*/
cvmx_pip_wqe_word2 word2;
/**
* Pointer to the first segment of the packet.
*/
cvmx_buf_ptr_t packet_ptr;
/**
* HW WRITE: octeon will fill in a programmable amount from the
* packet, up to (at most, but perhaps less) the amount
* needed to fill the work queue entry to 128 bytes
* If the packet is recognized to be IP, the hardware starts (except that
* the IPv4 header is padded for appropriate alignment) writing here where
* the IP header starts.
* If the packet is not recognized to be IP, the hardware starts writing
* the beginning of the packet here.
*/
uint8_t packet_data[96];
/**
* If desired, SW can make the work Q entry any length. For the
* purposes of discussion here, Assume 128B always, as this is all that
* the hardware deals with.
*
*/
} CVMX_CACHE_LINE_ALIGNED cvmx_wqe_t;
#ifdef __cplusplus
}
#endif
#endif /* __CVMX_WQE_H__ */