| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/usb/urtw/@/amd64/compile/hs32/modules/usr/src/sys/modules/nmdm/@/dev/cx/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/usb/urtw/@/amd64/compile/hs32/modules/usr/src/sys/modules/nmdm/@/dev/cx/csigma.c |
/*-
* Low-level subroutines for Cronyx-Sigma adapter.
*
* Copyright (C) 1994-2000 Cronyx Engineering.
* Author: Serge Vakulenko, <vak@cronyx.ru>
*
* This software is distributed with NO WARRANTIES, not even the implied
* warranties for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
*
* Authors grant any other persons or organisations permission to use
* or modify this software as long as this message is kept with the software,
* all derivative works or modified versions.
*
* Cronyx Id: csigma.c,v 1.1.2.1 2003/11/12 17:13:41 rik Exp $
* $FreeBSD: release/9.1.0/sys/dev/cx/csigma.c 139749 2005-01-06 01:43:34Z imp $
*/
#include <dev/cx/machdep.h>
#include <dev/cx/cxddk.h>
#include <dev/cx/cxreg.h>
#include <dev/cx/cronyxfw.h>
#define DMA_MASK 0xd4 /* DMA mask register */
#define DMA_MASK_CLEAR 0x04 /* DMA clear mask */
#define DMA_MODE 0xd6 /* DMA mode register */
#define DMA_MODE_MASTER 0xc0 /* DMA master mode */
#define BYTE *(unsigned char*)&
static unsigned char irqmask [] = {
BCR0_IRQ_DIS, BCR0_IRQ_DIS, BCR0_IRQ_DIS, BCR0_IRQ_3,
BCR0_IRQ_DIS, BCR0_IRQ_5, BCR0_IRQ_DIS, BCR0_IRQ_7,
BCR0_IRQ_DIS, BCR0_IRQ_DIS, BCR0_IRQ_10, BCR0_IRQ_11,
BCR0_IRQ_12, BCR0_IRQ_DIS, BCR0_IRQ_DIS, BCR0_IRQ_15,
};
static unsigned char dmamask [] = {
BCR0_DMA_DIS, BCR0_DMA_DIS, BCR0_DMA_DIS, BCR0_DMA_DIS,
BCR0_DMA_DIS, BCR0_DMA_5, BCR0_DMA_6, BCR0_DMA_7,
};
/* standard base port set */
static short porttab [] = {
0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0,
0x300, 0x320, 0x340, 0x360, 0x380, 0x3a0, 0x3c0, 0x3e0, 0
};
/* valid IRQs and DRQs */
static short irqtab [] = { 3, 5, 7, 10, 11, 12, 15, 0 };
static short dmatab [] = { 5, 6, 7, 0 };
static int valid (short value, short *list)
{
while (*list)
if (value == *list++)
return 1;
return 0;
}
long cx_rxbaud = 9600; /* receiver baud rate */
long cx_txbaud = 9600; /* transmitter baud rate */
int cx_univ_mode = M_HDLC; /* univ. chan. mode: async or sync */
int cx_sync_mode = M_HDLC; /* sync. chan. mode: HDLC, Bisync or X.21 */
int cx_iftype = 0; /* univ. chan. interface: upper/lower */
static int cx_probe_chip (port_t base);
static void cx_setup_chip (cx_chan_t *c);
/*
* Wait for CCR to clear.
*/
void cx_cmd (port_t base, int cmd)
{
port_t port = CCR(base);
int count;
/* Wait 10 msec for the previous command to complete. */
for (count=0; inb(port) && count<20000; ++count)
continue;
/* Issue the command. */
outb (port, cmd);
/* Wait 10 msec for the command to complete. */
for (count=0; inb(port) && count<20000; ++count)
continue;
}
/*
* Reset the chip.
*/
static int cx_reset (port_t port)
{
int count;
/* Wait up to 10 msec for revision code to appear after reset. */
for (count=0; count<20000; ++count)
if (inb(GFRCR(port)) != 0)
break;
cx_cmd (port, CCR_RSTALL);
/* Firmware revision code should clear imediately. */
/* Wait up to 10 msec for revision code to appear again. */
for (count=0; count<20000; ++count)
if (inb(GFRCR(port)) != 0)
return (1);
/* Reset failed. */
return (0);
}
int cx_download (port_t port, const unsigned char *firmware, long bits,
const cr_dat_tst_t *tst)
{
unsigned char cr2, sr;
long i, n, maxn = (bits + 7) / 8;
int v, b;
inb (BDET(port));
for (i=n=0; n<maxn; ++n) {
v = ((firmware[n] ^ ' ') << 1) | (firmware[n] >> 7 & 1);
for (b=0; b<7; b+=2, i+=2) {
if (i >= bits)
break;
cr2 = 0;
if (v >> b & 1) cr2 |= BCR2_TMS;
if (v >> b & 2) cr2 |= BCR2_TDI;
outb (BCR2(port), cr2);
sr = inb (BSR(port));
outb (BCR0(port), BCR0800_TCK);
outb (BCR0(port), 0);
if (i >= tst->end)
++tst;
if (i >= tst->start && (sr & BSR800_LERR))
return (0);
}
}
return (1);
}
/*
* Check if the Sigma-XXX board is present at the given base port.
*/
static int cx_probe_chained_board (port_t port, int *c0, int *c1)
{
int rev, i;
/* Read and check the board revision code. */
rev = inb (BSR(port));
*c0 = *c1 = 0;
switch (rev & BSR_VAR_MASK) {
case CRONYX_100: *c0 = 1; break;
case CRONYX_400: *c1 = 1; break;
case CRONYX_500: *c0 = *c1 = 1; break;
case CRONYX_410: *c0 = 1; break;
case CRONYX_810: *c0 = *c1 = 1; break;
case CRONYX_410s: *c0 = 1; break;
case CRONYX_810s: *c0 = *c1 = 1; break;
case CRONYX_440: *c0 = 1; break;
case CRONYX_840: *c0 = *c1 = 1; break;
case CRONYX_401: *c0 = 1; break;
case CRONYX_801: *c0 = *c1 = 1; break;
case CRONYX_401s: *c0 = 1; break;
case CRONYX_801s: *c0 = *c1 = 1; break;
case CRONYX_404: *c0 = 1; break;
case CRONYX_703: *c0 = *c1 = 1; break;
default: return (0); /* invalid variant code */
}
switch (rev & BSR_OSC_MASK) {
case BSR_OSC_20: /* 20 MHz */
case BSR_OSC_18432: /* 18.432 MHz */
break;
default:
return (0); /* oscillator frequency does not match */
}
for (i=2; i<0x10; i+=2)
if ((inb (BSR(port)+i) & BSR_REV_MASK) != (rev & BSR_REV_MASK))
return (0); /* status changed? */
return (1);
}
/*
* Check if the Sigma-800 board is present at the given base port.
* Read board status register 1 and check identification bits
* which should invert every next read.
*/
static int cx_probe_800_chained_board (port_t port)
{
unsigned char det, odet;
int i;
odet = inb (BDET(port));
if ((odet & (BDET_IB | BDET_IB_NEG)) != BDET_IB &&
(odet & (BDET_IB | BDET_IB_NEG)) != BDET_IB_NEG)
return (0);
for (i=0; i<100; ++i) {
det = inb (BDET(port));
if (((det ^ odet) & (BDET_IB | BDET_IB_NEG)) !=
(BDET_IB | BDET_IB_NEG))
return (0);
odet = det;
}
/* Reset the controller. */
outb (BCR0(port), 0);
outb (BCR1(port), 0);
outb (BCR2(port), 0);
return (1);
}
/*
* Check if the Sigma-2x board is present at the given base port.
*/
static int cx_probe_2x_board (port_t port)
{
int rev, i;
/* Read and check the board revision code. */
rev = inb (BSR(port));
if ((rev & BSR2X_VAR_MASK) != CRONYX_22 &&
(rev & BSR2X_VAR_MASK) != CRONYX_24)
return (0); /* invalid variant code */
for (i=2; i<0x10; i+=2)
if ((inb (BSR(port)+i) & BSR2X_REV_MASK) !=
(rev & BSR2X_REV_MASK))
return (0); /* status changed? */
return (1);
}
/*
* Check if the Cronyx-Sigma board is present at the given base port.
*/
int cx_probe_board (port_t port, int irq, int dma)
{
int c0, c1, c2=0, c3=0, result;
if (! valid (port, porttab))
return 0;
if (irq > 0 && ! valid (irq, irqtab))
return 0;
if (dma > 0 && ! valid (dma, dmatab))
return 0;
if (cx_probe_800_chained_board (port)) {
/* Sigma-800 detected. */
if (! (inb (BSR(port)) & BSR_NOCHAIN)) {
/* chained board attached */
if (! cx_probe_800_chained_board (port+0x10))
/* invalid chained board? */
return (0);
if (! (inb (BSR(port+0x10)) & BSR_NOCHAIN))
/* invalid chained board flag? */
return (0);
}
return 1;
}
if (cx_probe_chained_board (port, &c0, &c1)) {
/* Sigma-XXX detected. */
if (! (inb (BSR(port)) & BSR_NOCHAIN)) {
/* chained board attached */
if (! cx_probe_chained_board (port+0x10, &c2, &c3))
/* invalid chained board? */
return (0);
if (! (inb (BSR(port+0x10)) & BSR_NOCHAIN))
/* invalid chained board flag? */
return (0);
}
} else if (cx_probe_2x_board (port)) {
c0 = 1; /* Sigma-2x detected. */
c1 = 0;
} else
return (0); /* no board detected */
/* Turn off the reset bit. */
outb (BCR0(port), BCR0_NORESET);
if (c2 || c3)
outb (BCR0(port + 0x10), BCR0_NORESET);
result = 1;
if (c0 && ! cx_probe_chip (CS0(port)))
result = 0; /* no CD2400 chip here */
else if (c1 && ! cx_probe_chip (CS1A(port)) &&
! cx_probe_chip (CS1(port)))
result = 0; /* no second CD2400 chip */
else if (c2 && ! cx_probe_chip (CS0(port + 0x10)))
result = 0; /* no CD2400 chip on the slave board */
else if (c3 && ! cx_probe_chip (CS1(port + 0x10)))
result = 0; /* no second CD2400 chip on the slave board */
/* Reset the controller. */
outb (BCR0(port), 0);
if (c2 || c3)
outb (BCR0(port + 0x10), 0);
/* Yes, we really have valid Sigma board. */
return (result);
}
/*
* Check if the CD2400 chip is present at the given base port.
*/
static int cx_probe_chip (port_t base)
{
int rev, newrev, count;
/* Wait up to 10 msec for revision code to appear after reset. */
rev = 0;
for (count=0; rev==0; ++count) {
if (count >= 20000)
return (0); /* reset failed */
rev = inb (GFRCR(base));
}
/* Read and check the global firmware revision code. */
if (! (rev>=REVCL_MIN && rev<=REVCL_MAX) &&
! (rev>=REVCL31_MIN && rev<=REVCL31_MAX))
return (0); /* CD2400/2431 revision does not match */
/* Reset the chip. */
if (! cx_reset (base))
return (0);
/* Read and check the new global firmware revision code. */
newrev = inb (GFRCR(base));
if (newrev != rev)
return (0); /* revision changed */
/* Yes, we really have CD2400/2431 chip here. */
return (1);
}
/*
* Check that the irq is functional.
* irq>0 - activate the interrupt from the adapter (irq=on)
* irq<0 - deactivate the interrupt (irq=off)
* irq==0 - free the interrupt line (irq=tri-state)
* Return the interrupt mask _before_ activating irq.
*/
int cx_probe_irq (cx_board_t *b, int irq)
{
int mask, rev;
port_t port;
rev = inb (BSR(b->port));
port = ((rev & BSR_VAR_MASK) != CRONYX_400) ? CS0(b->port) : CS1(b->port);
outb (0x20, 0x0a);
mask = inb (0x20);
outb (0xa0, 0x0a);
mask |= inb (0xa0) << 8;
if (irq > 0) {
outb (BCR0(b->port), BCR0_NORESET | irqmask[irq]);
outb (CAR(port), 0);
cx_cmd (port, CCR_CLRCH);
outb (CMR(port), CMR_HDLC);
outb (TCOR(port), 0);
outb (TBPR(port), 1);
cx_cmd (port, CCR_INITCH | CCR_ENTX);
outb (IER(port), IER_TXMPTY);
} else if (irq < 0) {
cx_reset (port);
if (-irq > 7) {
outb (0xa0, 0x60 | ((-irq) & 7));
outb (0x20, 0x62);
} else
outb (0x20, 0x60 | (-irq));
} else
outb (BCR0(b->port), 0);
return mask;
}
static int cx_chip_revision (port_t port, int rev)
{
int count;
/* Model 400 has no first chip. */
port = ((rev & BSR_VAR_MASK) != CRONYX_400) ? CS0(port) : CS1(port);
/* Wait up to 10 msec for revision code to appear after reset. */
for (count=0; inb(GFRCR(port))==0; ++count)
if (count >= 20000)
return (0); /* reset failed */
return inb (GFRCR (port));
}
/*
* Probe and initialize the board structure.
*/
void cx_init (cx_board_t *b, int num, port_t port, int irq, int dma)
{
int gfrcr, rev, chain, mod = 0, rev2 = 0, mod2 = 0;
rev = inb (BSR(port));
chain = ! (rev & BSR_NOCHAIN);
if (cx_probe_800_chained_board (port)) {
cx_init_800 (b, num, port, irq, dma, chain);
return;
}
if ((rev & BSR2X_VAR_MASK) == CRONYX_22 ||
(rev & BSR2X_VAR_MASK) == CRONYX_24) {
cx_init_2x (b, num, port, irq, dma,
(rev & BSR2X_VAR_MASK), (rev & BSR2X_OSC_33));
return;
}
outb (BCR0(port), BCR0_NORESET);
if (chain)
outb (BCR0(port+0x10), BCR0_NORESET);
gfrcr = cx_chip_revision (port, rev);
if (gfrcr >= REVCL31_MIN && gfrcr <= REVCL31_MAX)
mod = 1;
if (chain) {
rev2 = inb (BSR(port+0x10));
gfrcr = cx_chip_revision (port+0x10, rev2);
if (gfrcr >= REVCL31_MIN && gfrcr <= REVCL31_MAX)
mod2 = 1;
outb (BCR0(port+0x10), 0);
}
outb (BCR0(port), 0);
cx_init_board (b, num, port, irq, dma, chain,
(rev & BSR_VAR_MASK), (rev & BSR_OSC_MASK), mod,
(rev2 & BSR_VAR_MASK), (rev2 & BSR_OSC_MASK), mod2);
}
/*
* Initialize the board structure, given the type of the board.
*/
void cx_init_board (cx_board_t *b, int num, port_t port, int irq, int dma,
int chain, int rev, int osc, int mod, int rev2, int osc2, int mod2)
{
cx_chan_t *c;
char *type;
int i;
/* Initialize board structure. */
b->port = port;
b->num = num;
b->irq = irq;
b->dma = dma;
b->opt = board_opt_dflt;
b->type = B_SIGMA_XXX;
b->if0type = b->if8type = cx_iftype;
/* Set channels 0 and 8 mode, set DMA and IRQ. */
b->bcr0 = b->bcr0b = BCR0_NORESET | dmamask[b->dma] | irqmask[b->irq];
/* Clear DTR[0..3] and DTR[8..12]. */
b->bcr1 = b->bcr1b = 0;
/*------------------ Master board -------------------*/
/* Read and check the board revision code. */
strcpy (b->name, mod ? "m" : "");
switch (rev) {
default: type = ""; break;
case CRONYX_100: type = "100"; break;
case CRONYX_400: type = "400"; break;
case CRONYX_500: type = "500"; break;
case CRONYX_410: type = "410"; break;
case CRONYX_810: type = "810"; break;
case CRONYX_410s: type = "410s"; break;
case CRONYX_810s: type = "810s"; break;
case CRONYX_440: type = "440"; break;
case CRONYX_840: type = "840"; break;
case CRONYX_401: type = "401"; break;
case CRONYX_801: type = "801"; break;
case CRONYX_401s: type = "401s"; break;
case CRONYX_801s: type = "801s"; break;
case CRONYX_404: type = "404"; break;
case CRONYX_703: type = "703"; break;
}
strcat (b->name, type);
switch (osc) {
default:
case BSR_OSC_20: /* 20 MHz */
b->chan[0].oscfreq = b->chan[1].oscfreq =
b->chan[2].oscfreq = b->chan[3].oscfreq =
b->chan[4].oscfreq = b->chan[5].oscfreq =
b->chan[6].oscfreq = b->chan[7].oscfreq =
mod ? 33000000L : 20000000L;
strcat (b->name, "a");
break;
case BSR_OSC_18432: /* 18.432 MHz */
b->chan[0].oscfreq = b->chan[1].oscfreq =
b->chan[2].oscfreq = b->chan[3].oscfreq =
b->chan[4].oscfreq = b->chan[5].oscfreq =
b->chan[6].oscfreq = b->chan[7].oscfreq =
mod ? 20000000L : 18432000L;
strcat (b->name, "b");
break;
}
/*------------------ Slave board -------------------*/
if (chain) {
/* Read and check the board revision code. */
strcat (b->name, mod2 ? "/m" : "/");
switch (rev2) {
default: type = ""; break;
case CRONYX_100: type = "100"; break;
case CRONYX_400: type = "400"; break;
case CRONYX_500: type = "500"; break;
case CRONYX_410: type = "410"; break;
case CRONYX_810: type = "810"; break;
case CRONYX_410s: type = "410s"; break;
case CRONYX_810s: type = "810s"; break;
case CRONYX_440: type = "440"; break;
case CRONYX_840: type = "840"; break;
case CRONYX_401: type = "401"; break;
case CRONYX_801: type = "801"; break;
case CRONYX_401s: type = "401s"; break;
case CRONYX_801s: type = "801s"; break;
case CRONYX_404: type = "404"; break;
case CRONYX_703: type = "703"; break;
}
strcat (b->name, type);
switch (osc2) {
default:
case BSR_OSC_20: /* 20 MHz */
b->chan[8].oscfreq = b->chan[9].oscfreq =
b->chan[10].oscfreq = b->chan[11].oscfreq =
b->chan[12].oscfreq = b->chan[13].oscfreq =
b->chan[14].oscfreq = b->chan[15].oscfreq =
mod2 ? 33000000L : 20000000L;
strcat (b->name, "a");
break;
case BSR_OSC_18432: /* 18.432 MHz */
b->chan[8].oscfreq = b->chan[9].oscfreq =
b->chan[10].oscfreq = b->chan[11].oscfreq =
b->chan[12].oscfreq = b->chan[13].oscfreq =
b->chan[14].oscfreq = b->chan[15].oscfreq =
mod2 ? 20000000L : 18432000L;
strcat (b->name, "b");
break;
}
}
/* Initialize channel structures. */
for (i=0; i<4; ++i) {
b->chan[i+0].port = CS0(port);
b->chan[i+4].port = cx_probe_chip (CS1A(port)) ?
CS1A(port) : CS1(port);
b->chan[i+8].port = CS0(port+0x10);
b->chan[i+12].port = CS1(port+0x10);
}
for (c=b->chan; c<b->chan+NCHAN; ++c) {
c->board = b;
c->num = c - b->chan;
c->type = T_NONE;
}
/*------------------ Master board -------------------*/
switch (rev) {
case CRONYX_400:
for (i=4; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_100:
b->chan[0].type = T_UNIV_RS232;
break;
case CRONYX_500:
b->chan[0].type = T_UNIV_RS232;
for (i=4; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_410:
b->chan[0].type = T_UNIV_V35;
for (i=1; i<4; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_810:
b->chan[0].type = T_UNIV_V35;
for (i=1; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_410s:
b->chan[0].type = T_UNIV_V35;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_RS232;
break;
case CRONYX_810s:
b->chan[0].type = T_UNIV_V35;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_RS232;
for (i=4; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_440:
b->chan[0].type = T_UNIV_V35;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_V35;
break;
case CRONYX_840:
b->chan[0].type = T_UNIV_V35;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_V35;
for (i=4; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_401:
b->chan[0].type = T_UNIV_RS449;
for (i=1; i<4; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_801:
b->chan[0].type = T_UNIV_RS449;
for (i=1; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_401s:
b->chan[0].type = T_UNIV_RS449;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_RS232;
break;
case CRONYX_801s:
b->chan[0].type = T_UNIV_RS449;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_RS232;
for (i=4; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_404:
b->chan[0].type = T_UNIV_RS449;
for (i=1; i<4; ++i)
b->chan[i].type = T_SYNC_RS449;
break;
case CRONYX_703:
b->chan[0].type = T_UNIV_RS449;
for (i=1; i<3; ++i)
b->chan[i].type = T_SYNC_RS449;
for (i=4; i<8; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
}
/*------------------ Slave board -------------------*/
if (chain) {
switch (rev2) {
case CRONYX_400:
break;
case CRONYX_100:
b->chan[8].type = T_UNIV_RS232;
break;
case CRONYX_500:
b->chan[8].type = T_UNIV_RS232;
for (i=12; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_410:
b->chan[8].type = T_UNIV_V35;
for (i=9; i<12; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_810:
b->chan[8].type = T_UNIV_V35;
for (i=9; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_410s:
b->chan[8].type = T_UNIV_V35;
for (i=9; i<12; ++i)
b->chan[i].type = T_SYNC_RS232;
break;
case CRONYX_810s:
b->chan[8].type = T_UNIV_V35;
for (i=9; i<12; ++i)
b->chan[i].type = T_SYNC_RS232;
for (i=12; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_440:
b->chan[8].type = T_UNIV_V35;
for (i=9; i<12; ++i)
b->chan[i].type = T_SYNC_V35;
break;
case CRONYX_840:
b->chan[8].type = T_UNIV_V35;
for (i=9; i<12; ++i)
b->chan[i].type = T_SYNC_V35;
for (i=12; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_401:
b->chan[8].type = T_UNIV_RS449;
for (i=9; i<12; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_801:
b->chan[8].type = T_UNIV_RS449;
for (i=9; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_401s:
b->chan[8].type = T_UNIV_RS449;
for (i=9; i<12; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_801s:
b->chan[8].type = T_UNIV_RS449;
for (i=9; i<12; ++i)
b->chan[i].type = T_SYNC_RS232;
for (i=12; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
case CRONYX_404:
b->chan[8].type = T_UNIV_RS449;
for (i=9; i<12; ++i)
b->chan[i].type = T_SYNC_RS449;
break;
case CRONYX_703:
b->chan[8].type = T_UNIV_RS449;
for (i=9; i<11; ++i)
b->chan[i].type = T_SYNC_RS449;
for (i=12; i<16; ++i)
b->chan[i].type = T_UNIV_RS232;
break;
}
}
b->nuniv = b->nsync = b->nasync = 0;
for (c=b->chan; c<b->chan+NCHAN; ++c)
switch (c->type) {
case T_ASYNC: ++b->nasync; break;
case T_UNIV:
case T_UNIV_RS232:
case T_UNIV_RS449:
case T_UNIV_V35: ++b->nuniv; break;
case T_SYNC_RS232:
case T_SYNC_V35:
case T_SYNC_RS449: ++b->nsync; break;
}
cx_reinit_board (b);
}
/*
* Initialize the Sigma-800 board structure.
*/
void cx_init_800 (cx_board_t *b, int num, port_t port, int irq, int dma,
int chain)
{
cx_chan_t *c;
int i;
/* Initialize board structure. */
b->port = port;
b->num = num;
b->irq = irq;
b->dma = dma;
b->opt = board_opt_dflt;
b->type = B_SIGMA_800;
/* Set channels 0 and 8 mode, set DMA and IRQ. */
b->bcr0 = b->bcr0b = dmamask[b->dma] | irqmask[b->irq];
/* Clear DTR[0..7] and DTR[8..15]. */
b->bcr1 = b->bcr1b = 0;
strcpy (b->name, "800");
if (chain)
strcat (b->name, "/800");
/* Initialize channel structures. */
for (i=0; i<4; ++i) {
b->chan[i+0].port = CS0(port);
b->chan[i+4].port = cx_probe_chip (CS1A(port)) ?
CS1A(port) : CS1(port);
b->chan[i+8].port = CS0(port+0x10);
b->chan[i+12].port = CS1(port+0x10);
}
for (c=b->chan; c<b->chan+NCHAN; ++c) {
c->board = b;
c->num = c - b->chan;
c->oscfreq = 33000000L;
c->type = (c->num < 8 || chain) ? T_UNIV_RS232 : T_NONE;
}
b->nuniv = b->nsync = b->nasync = 0;
for (c=b->chan; c<b->chan+NCHAN; ++c)
switch (c->type) {
case T_ASYNC: ++b->nasync; break;
case T_UNIV:
case T_UNIV_RS232:
case T_UNIV_RS449:
case T_UNIV_V35: ++b->nuniv; break;
case T_SYNC_RS232:
case T_SYNC_V35:
case T_SYNC_RS449: ++b->nsync; break;
}
cx_reinit_board (b);
}
/*
* Initialize the Sigma-2x board structure.
*/
void cx_init_2x (cx_board_t *b, int num, port_t port, int irq, int dma,
int rev, int osc)
{
cx_chan_t *c;
int i;
/* Initialize board structure. */
b->port = port;
b->num = num;
b->irq = irq;
b->dma = dma;
b->opt = board_opt_dflt;
b->type = B_SIGMA_2X;
/* Set channels 0 and 8 mode, set DMA and IRQ. */
b->bcr0 = BCR0_NORESET | dmamask[b->dma] | irqmask[b->irq];
if (b->type == B_SIGMA_2X && b->opt.fast)
b->bcr0 |= BCR02X_FAST;
/* Clear DTR[0..3] and DTR[8..12]. */
b->bcr1 = 0;
/* Initialize channel structures. */
for (i=0; i<4; ++i) {
b->chan[i+0].port = CS0(port);
b->chan[i+4].port = CS1(port);
b->chan[i+8].port = CS0(port+0x10);
b->chan[i+12].port = CS1(port+0x10);
}
for (c=b->chan; c<b->chan+NCHAN; ++c) {
c->board = b;
c->num = c - b->chan;
c->type = T_NONE;
c->oscfreq = (osc & BSR2X_OSC_33) ? 33000000L : 20000000L;
}
/* Check the board revision code. */
strcpy (b->name, "22");
b->chan[0].type = T_UNIV;
b->chan[1].type = T_UNIV;
b->nsync = b->nasync = 0;
b->nuniv = 2;
if (rev == CRONYX_24) {
strcpy (b->name, "24");
b->chan[2].type = T_UNIV;
b->chan[3].type = T_UNIV;
b->nuniv += 2;
}
strcat (b->name, (osc & BSR2X_OSC_33) ? "c" : "a");
cx_reinit_board (b);
}
/*
* Reinitialize all channels, using new options and baud rate.
*/
void cx_reinit_board (cx_board_t *b)
{
cx_chan_t *c;
b->opt = board_opt_dflt;
if (b->type == B_SIGMA_2X) {
b->bcr0 &= ~BCR02X_FAST;
if (b->opt.fast)
b->bcr0 |= BCR02X_FAST;
} else
b->if0type = b->if8type = cx_iftype;
for (c=b->chan; c<b->chan+NCHAN; ++c) {
switch (c->type) {
default:
case T_NONE:
continue;
case T_UNIV:
case T_UNIV_RS232:
case T_UNIV_RS449:
case T_UNIV_V35:
c->mode = (cx_univ_mode == M_ASYNC) ?
M_ASYNC : cx_sync_mode;
break;
case T_SYNC_RS232:
case T_SYNC_V35:
case T_SYNC_RS449:
c->mode = cx_sync_mode;
break;
case T_ASYNC:
c->mode = M_ASYNC;
break;
}
c->rxbaud = cx_rxbaud;
c->txbaud = cx_txbaud;
c->opt = chan_opt_dflt;
c->aopt = opt_async_dflt;
c->hopt = opt_hdlc_dflt;
}
}
/*
* Set up the board.
*/
int cx_setup_board (cx_board_t *b, const unsigned char *firmware,
long bits, const cr_dat_tst_t *tst)
{
int i;
#ifndef NDIS_MINIPORT_DRIVER
/* Disable DMA channel. */
outb (DMA_MASK, (b->dma & 3) | DMA_MASK_CLEAR);
#endif
/* Reset the controller. */
outb (BCR0(b->port), 0);
if (b->chan[8].type || b->chan[12].type)
outb (BCR0(b->port+0x10), 0);
/* Load the firmware. */
if (b->type == B_SIGMA_800) {
/* Reset the controllers. */
outb (BCR2(b->port), BCR2_TMS);
if (b->chan[8].type || b->chan[12].type)
outb (BCR2(b->port+0x10), BCR2_TMS);
outb (BCR2(b->port), 0);
if (b->chan[8].type || b->chan[12].type)
outb (BCR2(b->port+0x10), 0);
if (firmware &&
(! cx_download (b->port, firmware, bits, tst) ||
((b->chan[8].type || b->chan[12].type) &&
! cx_download (b->port+0x10, firmware, bits, tst))))
return (0);
}
/*
* Set channels 0 and 8 to RS232 async. mode.
* Enable DMA and IRQ.
*/
outb (BCR0(b->port), b->bcr0);
if (b->chan[8].type || b->chan[12].type)
outb (BCR0(b->port+0x10), b->bcr0b);
/* Clear DTR[0..3] and DTR[8..12]. */
outw (BCR1(b->port), b->bcr1);
if (b->chan[8].type || b->chan[12].type)
outw (BCR1(b->port+0x10), b->bcr1b);
if (b->type == B_SIGMA_800)
outb (BCR2(b->port), b->opt.fast &
(BCR2_BUS0 | BCR2_BUS1));
/* Initialize all controllers. */
for (i=0; i<NCHAN; i+=4)
if (b->chan[i].type != T_NONE)
cx_setup_chip (b->chan + i);
#ifndef NDIS_MINIPORT_DRIVER
/* Set up DMA channel to master mode. */
outb (DMA_MODE, (b->dma & 3) | DMA_MODE_MASTER);
/* Enable DMA channel. */
outb (DMA_MASK, b->dma & 3);
#endif
/* Initialize all channels. */
for (i=0; i<NCHAN; ++i)
if (b->chan[i].type != T_NONE)
cx_setup_chan (b->chan + i);
return (1);
}
/*
* Initialize the board.
*/
static void cx_setup_chip (cx_chan_t *c)
{
/* Reset the chip. */
cx_reset (c->port);
/*
* Set all interrupt level registers to the same value.
* This enables the internal CD2400 priority scheme.
*/
outb (RPILR(c->port), BRD_INTR_LEVEL);
outb (TPILR(c->port), BRD_INTR_LEVEL);
outb (MPILR(c->port), BRD_INTR_LEVEL);
/* Set bus error count to zero. */
outb (BERCNT(c->port), 0);
/* Set 16-bit DMA mode. */
outb (DMR(c->port), 0);
/* Set timer period register to 1 msec (approximately). */
outb (TPR(c->port), 10);
}
/*
* Initialize the CD2400 channel.
*/
void cx_update_chan (cx_chan_t *c)
{
int clock, period;
if (c->board->type == B_SIGMA_XXX)
switch (c->num) {
case 0:
c->board->bcr0 &= ~BCR0_UMASK;
if (c->mode != M_ASYNC)
c->board->bcr0 |= BCR0_UM_SYNC;
if (c->board->if0type &&
(c->type==T_UNIV_RS449 || c->type==T_UNIV_V35))
c->board->bcr0 |= BCR0_UI_RS449;
outb (BCR0(c->board->port), c->board->bcr0);
break;
case 8:
c->board->bcr0b &= ~BCR0_UMASK;
if (c->mode != M_ASYNC)
c->board->bcr0b |= BCR0_UM_SYNC;
if (c->board->if8type &&
(c->type==T_UNIV_RS449 || c->type==T_UNIV_V35))
c->board->bcr0b |= BCR0_UI_RS449;
outb (BCR0(c->board->port+0x10), c->board->bcr0b);
break;
}
/* set current channel number */
outb (CAR(c->port), c->num & 3);
switch (c->mode) { /* initialize the channel mode */
case M_ASYNC:
/* set receiver timeout register */
outw (RTPR(c->port), 10); /* 10 msec, see TPR */
c->opt.rcor.encod = ENCOD_NRZ;
outb (CMR(c->port), CMR_RXDMA | CMR_TXDMA | CMR_ASYNC);
outb (COR1(c->port), BYTE c->aopt.cor1);
outb (COR2(c->port), BYTE c->aopt.cor2);
outb (COR3(c->port), BYTE c->aopt.cor3);
outb (COR6(c->port), BYTE c->aopt.cor6);
outb (COR7(c->port), BYTE c->aopt.cor7);
outb (SCHR1(c->port), c->aopt.schr1);
outb (SCHR2(c->port), c->aopt.schr2);
outb (SCHR3(c->port), c->aopt.schr3);
outb (SCHR4(c->port), c->aopt.schr4);
outb (SCRL(c->port), c->aopt.scrl);
outb (SCRH(c->port), c->aopt.scrh);
outb (LNXT(c->port), c->aopt.lnxt);
break;
case M_HDLC:
outb (CMR(c->port), CMR_RXDMA | CMR_TXDMA | CMR_HDLC);
outb (COR1(c->port), BYTE c->hopt.cor1);
outb (COR2(c->port), BYTE c->hopt.cor2);
outb (COR3(c->port), BYTE c->hopt.cor3);
outb (RFAR1(c->port), c->hopt.rfar1);
outb (RFAR2(c->port), c->hopt.rfar2);
outb (RFAR3(c->port), c->hopt.rfar3);
outb (RFAR4(c->port), c->hopt.rfar4);
outb (CPSR(c->port), c->hopt.cpsr);
break;
}
/* set mode-independent options */
outb (COR4(c->port), BYTE c->opt.cor4);
outb (COR5(c->port), BYTE c->opt.cor5);
/* set up receiver clock values */
if (c->mode == M_ASYNC || c->opt.rcor.dpll || c->opt.tcor.llm) {
cx_clock (c->oscfreq, c->rxbaud, &clock, &period);
c->opt.rcor.clk = clock;
} else {
c->opt.rcor.clk = CLK_EXT;
period = 1;
}
outb (RCOR(c->port), BYTE c->opt.rcor);
outb (RBPR(c->port), period);
/* set up transmitter clock values */
if (c->mode == M_ASYNC || !c->opt.tcor.ext1x) {
unsigned ext1x = c->opt.tcor.ext1x;
c->opt.tcor.ext1x = 0;
cx_clock (c->oscfreq, c->txbaud, &clock, &period);
c->opt.tcor.clk = clock;
c->opt.tcor.ext1x = ext1x;
} else {
c->opt.tcor.clk = CLK_EXT;
period = 1;
}
outb (TCOR(c->port), BYTE c->opt.tcor);
outb (TBPR(c->port), period);
}
/*
* Initialize the CD2400 channel.
*/
void cx_setup_chan (cx_chan_t *c)
{
/* set current channel number */
outb (CAR(c->port), c->num & 3);
/* reset the channel */
cx_cmd (c->port, CCR_CLRCH);
/* set LIVR to contain the board and channel numbers */
outb (LIVR(c->port), c->board->num << 6 | c->num << 2);
/* clear DTR, RTS, set TXCout/DTR pin */
outb (MSVR_RTS(c->port), 0);
outb (MSVR_DTR(c->port), c->mode==M_ASYNC ? 0 : MSV_TXCOUT);
/* set receiver A buffer physical address */
outw (ARBADRU(c->port), (unsigned short) (c->arphys>>16));
outw (ARBADRL(c->port), (unsigned short) c->arphys);
/* set receiver B buffer physical address */
outw (BRBADRU(c->port), (unsigned short) (c->brphys>>16));
outw (BRBADRL(c->port), (unsigned short) c->brphys);
/* set transmitter A buffer physical address */
outw (ATBADRU(c->port), (unsigned short) (c->atphys>>16));
outw (ATBADRL(c->port), (unsigned short) c->atphys);
/* set transmitter B buffer physical address */
outw (BTBADRU(c->port), (unsigned short) (c->btphys>>16));
outw (BTBADRL(c->port), (unsigned short) c->btphys);
c->dtr = 0;
c->rts = 0;
cx_update_chan (c);
}
/*
* Control DTR signal for the channel.
* Turn it on/off.
*/
void cx_set_dtr (cx_chan_t *c, int on)
{
cx_board_t *b = c->board;
c->dtr = on ? 1 : 0;
if (b->type == B_SIGMA_2X) {
if (on) b->bcr1 |= BCR1_DTR(c->num);
else b->bcr1 &= ~BCR1_DTR(c->num);
outw (BCR1(b->port), b->bcr1);
return;
}
if (b->type == B_SIGMA_800) {
if (c->num >= 8) {
if (on) b->bcr1b |= BCR1800_DTR(c->num);
else b->bcr1b &= ~BCR1800_DTR(c->num);
outb (BCR1(b->port+0x10), b->bcr1b);
} else {
if (on) b->bcr1 |= BCR1800_DTR(c->num);
else b->bcr1 &= ~BCR1800_DTR(c->num);
outb (BCR1(b->port), b->bcr1);
}
return;
}
if (c->mode == M_ASYNC) {
outb (CAR(c->port), c->num & 3);
outb (MSVR_DTR(c->port), on ? MSV_DTR : 0);
return;
}
switch (c->num) {
default:
/* Channels 4..7 and 12..15 in syncronous mode
* have no DTR signal. */
break;
case 1: case 2: case 3:
if (c->type == T_UNIV_RS232)
break;
case 0:
if (on) b->bcr1 |= BCR1_DTR(c->num);
else b->bcr1 &= ~BCR1_DTR(c->num);
outw (BCR1(b->port), b->bcr1);
break;
case 9: case 10: case 11:
if (c->type == T_UNIV_RS232)
break;
case 8:
if (on) b->bcr1b |= BCR1_DTR(c->num & 3);
else b->bcr1b &= ~BCR1_DTR(c->num & 3);
outw (BCR1(b->port+0x10), b->bcr1b);
break;
}
}
/*
* Control RTS signal for the channel.
* Turn it on/off.
*/
void cx_set_rts (cx_chan_t *c, int on)
{
c->rts = on ? 1 : 0;
outb (CAR(c->port), c->num & 3);
outb (MSVR_RTS(c->port), on ? MSV_RTS : 0);
}
/*
* Get the state of DSR signal of the channel.
*/
int cx_get_dsr (cx_chan_t *c)
{
unsigned char sigval;
if (c->board->type == B_SIGMA_2X ||
c->board->type == B_SIGMA_800 ||
c->mode == M_ASYNC) {
outb (CAR(c->port), c->num & 3);
return (inb (MSVR(c->port)) & MSV_DSR ? 1 : 0);
}
/*
* Channels 4..7 and 12..15 don't have DSR signal available.
*/
switch (c->num) {
default:
return (1);
case 1: case 2: case 3:
if (c->type == T_UNIV_RS232)
return (1);
case 0:
sigval = inw (BSR(c->board->port)) >> 8;
break;
case 9: case 10: case 11:
if (c->type == T_UNIV_RS232)
return (1);
case 8:
sigval = inw (BSR(c->board->port+0x10)) >> 8;
break;
}
return (~sigval >> (c->num & 3) & 1);
}
/*
* Get the state of CARRIER signal of the channel.
*/
int cx_get_cd (cx_chan_t *c)
{
unsigned char sigval;
if (c->board->type == B_SIGMA_2X ||
c->board->type == B_SIGMA_800 ||
c->mode == M_ASYNC) {
outb (CAR(c->port), c->num & 3);
return (inb (MSVR(c->port)) & MSV_CD ? 1 : 0);
}
/*
* Channels 4..7 and 12..15 don't have CD signal available.
*/
switch (c->num) {
default:
return (1);
case 1: case 2: case 3:
if (c->type == T_UNIV_RS232)
return (1);
case 0:
sigval = inw (BSR(c->board->port)) >> 8;
break;
case 9: case 10: case 11:
if (c->type == T_UNIV_RS232)
return (1);
case 8:
sigval = inw (BSR(c->board->port+0x10)) >> 8;
break;
}
return (~sigval >> 4 >> (c->num & 3) & 1);
}
/*
* Get the state of CTS signal of the channel.
*/
int cx_get_cts (cx_chan_t *c)
{
outb (CAR(c->port), c->num & 3);
return (inb (MSVR(c->port)) & MSV_CTS ? 1 : 0);
}
/*
* Compute CD2400 clock values.
*/
void cx_clock (long hz, long ba, int *clk, int *div)
{
static short clocktab[] = { 8, 32, 128, 512, 2048, 0 };
for (*clk=0; clocktab[*clk]; ++*clk) {
long c = ba * clocktab[*clk];
if (hz <= c*256) {
*div = (2 * hz + c) / (2 * c) - 1;
return;
}
}
/* Incorrect baud rate. Return some meaningful values. */
*clk = 0;
*div = 255;
}
/*
* Turn LED on/off.
*/
void cx_led (cx_board_t *b, int on)
{
switch (b->type) {
case B_SIGMA_2X:
if (on) b->bcr0 |= BCR02X_LED;
else b->bcr0 &= ~BCR02X_LED;
outb (BCR0(b->port), b->bcr0);
break;
}
}
void cx_disable_dma (cx_board_t *b)
{
#ifndef NDIS_MINIPORT_DRIVER
/* Disable DMA channel. */
outb (DMA_MASK, (b->dma & 3) | DMA_MASK_CLEAR);
#endif
}
cx_board_opt_t board_opt_dflt = { /* board options */
BUS_NORMAL, /* normal bus master timing */
};
cx_chan_opt_t chan_opt_dflt = { /* mode-independent options */
{ /* cor4 */
7, /* FIFO threshold, odd is better */
0,
0, /* don't detect 1 to 0 on CTS */
1, /* detect 1 to 0 on CD */
0, /* detect 1 to 0 on DSR */
},
{ /* cor5 */
0, /* receive flow control FIFO threshold */
0,
0, /* don't detect 0 to 1 on CTS */
1, /* detect 0 to 1 on CD */
0, /* detect 0 to 1 on DSR */
},
{ /* rcor */
0, /* dummy clock source */
ENCOD_NRZ, /* NRZ mode */
0, /* disable DPLL */
0,
0, /* transmit line value */
},
{ /* tcor */
0,
0, /* local loopback mode */
0,
1, /* external 1x clock mode */
0,
0, /* dummy transmit clock source */
},
};
cx_opt_async_t opt_async_dflt = { /* default async options */
{ /* cor1 */
8-1, /* 8-bit char length */
0, /* don't ignore parity */
PARM_NOPAR, /* no parity */
PAR_EVEN, /* even parity */
},
{ /* cor2 */
0, /* disable automatic DSR */
1, /* enable automatic CTS */
0, /* disable automatic RTS */
0, /* no remote loopback */
0,
0, /* disable embedded cmds */
0, /* disable XON/XOFF */
0, /* disable XANY */
},
{ /* cor3 */
STOPB_1, /* 1 stop bit */
0,
0, /* disable special char detection */
FLOWCC_PASS, /* pass flow ctl chars to the host */
0, /* range detect disable */
0, /* disable extended spec. char detect */
},
{ /* cor6 */
PERR_INTR, /* generate exception on parity errors */
BRK_INTR, /* generate exception on break condition */
0, /* don't translate NL to CR on input */
0, /* don't translate CR to NL on input */
0, /* don't discard CR on input */
},
{ /* cor7 */
0, /* don't translate CR to NL on output */
0, /* don't translate NL to CR on output */
0,
0, /* don't process flow ctl err chars */
0, /* disable LNext option */
0, /* don't strip 8 bit on input */
},
0, 0, 0, 0, 0, 0, 0, /* clear schr1-4, scrl, scrh, lnxt */
};
cx_opt_hdlc_t opt_hdlc_dflt = { /* default hdlc options */
{ /* cor1 */
2, /* 2 inter-frame flags */
0, /* no-address mode */
CLRDET_DISABLE, /* disable clear detect */
AFLO_1OCT, /* 1-byte address field length */
},
{ /* cor2 */
0, /* disable automatic DSR */
0, /* disable automatic CTS */
0, /* disable automatic RTS */
0,
CRC_INVERT, /* use CRC V.41 */
0,
FCS_NOTPASS, /* don't pass received CRC to the host */
0,
},
{ /* cor3 */
0, /* 0 pad characters sent */
IDLE_FLAG, /* idle in flag */
0, /* enable FCS */
FCSP_ONES, /* FCS preset to all ones (V.41) */
SYNC_AA, /* use AAh as sync char */
0, /* disable pad characters */
},
0, 0, 0, 0, /* clear rfar1-4 */
POLY_V41, /* use V.41 CRC polynomial */
};