| Current Path : /sys/amd64/compile/hs32/modules/usr/src/sys/modules/wlan_ccmp/@/dev/mii/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //sys/amd64/compile/hs32/modules/usr/src/sys/modules/wlan_ccmp/@/dev/mii/icsphyreg.h |
/* $NetBSD: icsphyreg.h,v 1.2 2003/07/01 22:46:08 msaitoh Exp $ */ /*- * Copyright (c) 1998 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, * NASA Ames Research Center. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD: release/9.1.0/sys/dev/mii/icsphyreg.h 204646 2010-03-03 17:55:51Z joel $ */ #ifndef _DEV_MII_ICSPHYREG_H_ #define _DEV_MII_ICSPHYREG_H_ /* * ICS1890 registers. * http://www.icst.com/pdf/18??.pdf */ /* HEX 1889 1890 1892 1893 *-------------------------------------------------------------- * 0 Control * * * * * 1 Status * * * * * 2 PHY Identifier * * * * * 3 PHY Identifier * * * * * 4 Auto-Neg. Advertisement * * * * 5 Auto-Neg. Link Parent Adv * * * * 6 Auto-Neg. Expansion * * * * 7 Auto-Neg. Next Page Tx * * * 8 ANg Nxt Page Lnk Parnt Abl * * * 10 Extended Control * * * * * 11 Quick Poll Status * * * * * 12 10Base-T Operation * * * * 13 Extended Control2 * * * */ #define MII_ICSPHY_ECR 0x10 /* Extended Control Register */ #define ECR_OVR 0x8000 /* disable command reg overwrites */ #define ECR_PHYADDR_MASK 0x07c0 /* PHY address mask */ #define ECR_CTEST 0x0020 /* Stream Cipher Test Mode */ #define ECR_IECT 0x0004 /* Invalid Error Code Test */ #define ECR_SSD 0x0001 /* Stream Cipher Disable */ #define MII_ICSPHY_QPR 0x11 /* Quick Poll Register */ #define QPR_SPEED 0x8000 /* 100Mbps */ #define QPR_FDX 0x4000 /* Full dupled */ #define QPR_ANB2 0x2000 /* Autoneg monitor bit 2 */ #define QPR_ANB1 0x1000 /* Autoneg monitor bit 1 */ #define QPR_ANB0 0x0800 /* Autoneg monitor bit 0 */ #define QPR_RXERR 0x0400 /* Receive signal lost */ #define QPR_PLLERR 0x0200 /* PLL error */ #define QPR_FCARR 0x0100 /* False carrier detected */ #define QPR_INVALSYM 0x0080 /* Invalid Symbol Detected */ #define QPR_HALT 0x0040 /* Halt Symbol Detected */ #define QPR_PREEM 0x0020 /* Two Idle Symbols together */ #define QPR_ACOMP 0x0010 /* Autonegotiation complete */ #define QPR_SDETECT 0x0008 /* signal detect */ #define QPR_JABBER 0x0004 /* Jabber detected */ #define QPR_RFAULT 0x0002 /* Remote Fault */ #define QPR_LINK 0x0001 /* Link */ #define MII_ICSPHY_TTR 0x12 /* 10baseT Operations Register */ #define TTR_RJABBER 0x8000 /* Remote Jabber */ #define TTR_POLARITY 0x4000 /* Polarity Reversed */ #define TTR_NOJABBER 0x0020 /* Disable Jabber Check */ #define TTR_LOOP 0x0010 /* Loopback mode */ #define TTR_NOAPOLARITY 0x0008 /* Disable auto polarity correction */ #define TTR_NOSQE 0x0004 /* Disable SQE check */ #define TTR_NOLINK 0x0002 /* Disable Link check */ #define TTR_NOSQUELCH 0x0001 /* Disable squelch */ /* * Extended Control Register 2 * * HEX 1889 1890 1892 1893 *------------------------------------------------------------------- * 8000 Node/Repeater Mode * * * * 4000 Hardware/Software Mode * * * * 2000 Link Partner Support Remote Flt * * 2000 Remote Fault * * * 1000 * 0800 * 0400 Xmitted Remote Fault status * * 0200 * 0100 * 0080 Tri-state Enable * * 0040 * 0020 * 0010 A-N Powerup Remote Flt * * 0008 * 0004 * 0002 Automatic 10Base-T Power Down * * 0001 Automatic 100Base-TX Power Down * * * */ #define MII_ICSPHY_ECR2 0x13 /* Extended Control Register 2 */ #define ECR2_REPEATER 0x8000 /* Repeater Mode */ #define ECR2_HWSW 0x4000 /* hw/sw config priority */ #define ECR2_LPRF 0x2000 /* link partner supports rem fault */ #define ECR2_FORCERF 0x0400 /* Force transmit of rem fault */ #define ECR2_RFPUP 0x0010 /* A-N Powerup Remote fault */ #define ECR2_10AUTOPWRDN 0x0002 /* Automatic 10baseT power down */ #define ECR2_100AUTOPWRDN 0x0001 /* Automatic 100baseTX power down */ #endif /* _DEV_MII_ICSPHYREG_H_ */