Current Path : /usr/src/etc/defaults/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
Current File : //usr/src/etc/defaults/bluetooth.device.conf |
# Copyright (c) 2005 Maksim Yevmenkin <m_evmenkin@yahoo.com> # All rights reserved. # # Redistribution and use in source and binary forms, with or without # modification, are permitted provided that the following conditions # are met: # 1. Redistributions of source code must retain the above copyright # notice, this list of conditions and the following disclaimer. # 2. Redistributions in binary form must reproduce the above copyright # notice, this list of conditions and the following disclaimer in the # documentation and/or other materials provided with the distribution. # # THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND # ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE # IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE # ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE # FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL # DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS # OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) # HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT # LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY # OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF # SUCH DAMAGE. # # $FreeBSD: release/9.1.0/etc/defaults/bluetooth.device.conf 179360 2008-05-27 17:46:32Z emax $ # The authentication_enable parameter controls if the device requires to # authenticate the remote device at connection setup. At connection setup, # only the devices with the authentication_enable parameter enabled will # try to authenticate the other device. # # Possible values: # # NO or 0 authentication disabled (default); # YES or 1 authentication enabled. # authentication_enable="NO" # The class parameter is used to indicate the capabilities of the device to # other devices. # # For more details see "Assigned Numbers - Bluetooth Baseband" document # # Possible value: # # xx:xx:xx where xx is a hex number # class="ff:01:0c" # The connectable parameter controls whether or not the device should # periodically scan for page attempts from other devices. # # Possible values: # # NO or 0 do not scan for page attempts; # YES or 1 scan for page attempts (default). # connectable="YES" # The discoverable parameter controls whether or not the device should # periodically scan for inquiry requests from other devices. # # Possible values: # # NO or 0 do not scan for inquiry requests; # YES or 1 scan for inquiry requests (default). # discoverable="YES" # The encryption_mode parameter controls if the device requires encryption # to the remote device at connection setup. At connection setup, only the # devices with the authentication_enable parameter enabled and encryption_mode # parameter enabled will try to encrypt the connection to the other device. # # Possible values: # # NONE or 0 encryption disabled (default); # P2P or 1 encryption only for point-to-point packets; # ALL or 2 encryption for both point-to-point and broadcast packets. # encryption_mode="NONE" # HCI node debug level. Higher values mean more verbose output. # # Possible values: 0 - 4 # hci_debug_level="3" # L2CAP node debug level. Higher values mean more verbose output. # # Possible values: 0 - 4 # l2cap_debug_level="3" # The local_name parameter provides the ability to modify the user friendly # name for the device. # local_name="My device" # The role_switch parameter controls whether the local device should perform # role switch. By default, if role switch is supported, the local device will # try to perform role switch and become Master on incoming connection. Some # devices do not support role switch and thus incoming connections from such # devices will fail. If role switch is disabled then accepting device will # remain Slave. # # NO or 0 do not perform role switch; # YES or 1 perform role switch (default). # role_switch="YES"