| Current Path : /usr/src/sys/sparc64/pci/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //usr/src/sys/sparc64/pci/psycho.c |
/*-
* Copyright (c) 1999, 2000 Matthew R. Green
* Copyright (c) 2001 - 2003 by Thomas Moestl <tmm@FreeBSD.org>
* Copyright (c) 2005 - 2006 Marius Strobl <marius@FreeBSD.org>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* from: NetBSD: psycho.c,v 1.39 2001/10/07 20:30:41 eeh Exp
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD: release/9.1.0/sys/sparc64/pci/psycho.c 230687 2012-01-28 23:53:06Z marius $");
/*
* Support for `Hummingbird' (UltraSPARC IIe), `Psycho' and `Psycho+'
* (UltraSPARC II) and `Sabre' (UltraSPARC IIi) UPA to PCI bridges.
*/
#include "opt_ofw_pci.h"
#include "opt_psycho.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/bus.h>
#include <sys/endian.h>
#include <sys/kdb.h>
#include <sys/kernel.h>
#include <sys/lock.h>
#include <sys/malloc.h>
#include <sys/module.h>
#include <sys/mutex.h>
#include <sys/pcpu.h>
#include <sys/reboot.h>
#include <sys/rman.h>
#include <dev/ofw/ofw_bus.h>
#include <dev/ofw/ofw_pci.h>
#include <dev/ofw/openfirm.h>
#include <machine/bus.h>
#include <machine/bus_common.h>
#include <machine/bus_private.h>
#include <machine/iommureg.h>
#include <machine/iommuvar.h>
#include <machine/resource.h>
#include <machine/ver.h>
#include <dev/pci/pcireg.h>
#include <dev/pci/pcivar.h>
#include <sparc64/pci/ofw_pci.h>
#include <sparc64/pci/psychoreg.h>
#include <sparc64/pci/psychovar.h>
#include "pcib_if.h"
static const struct psycho_desc *psycho_find_desc(const struct psycho_desc *,
const char *);
static const struct psycho_desc *psycho_get_desc(device_t);
static void psycho_set_intr(struct psycho_softc *, u_int, bus_addr_t,
driver_filter_t, driver_intr_t);
static int psycho_find_intrmap(struct psycho_softc *, u_int, bus_addr_t *,
bus_addr_t *, u_long *);
static void sabre_dmamap_sync(bus_dma_tag_t dt, bus_dmamap_t map,
bus_dmasync_op_t op);
static void psycho_intr_enable(void *);
static void psycho_intr_disable(void *);
static void psycho_intr_assign(void *);
static void psycho_intr_clear(void *);
/* Interrupt handlers */
static driver_filter_t psycho_ue;
static driver_filter_t psycho_ce;
static driver_filter_t psycho_pci_bus;
static driver_filter_t psycho_powerfail;
static driver_intr_t psycho_overtemp;
#ifdef PSYCHO_MAP_WAKEUP
static driver_filter_t psycho_wakeup;
#endif
/* IOMMU support */
static void psycho_iommu_init(struct psycho_softc *, int, uint32_t);
/*
* Methods
*/
static device_probe_t psycho_probe;
static device_attach_t psycho_attach;
static bus_read_ivar_t psycho_read_ivar;
static bus_setup_intr_t psycho_setup_intr;
static bus_alloc_resource_t psycho_alloc_resource;
static bus_activate_resource_t psycho_activate_resource;
static bus_adjust_resource_t psycho_adjust_resource;
static bus_get_dma_tag_t psycho_get_dma_tag;
static pcib_maxslots_t psycho_maxslots;
static pcib_read_config_t psycho_read_config;
static pcib_write_config_t psycho_write_config;
static pcib_route_interrupt_t psycho_route_interrupt;
static ofw_bus_get_node_t psycho_get_node;
static ofw_pci_setup_device_t psycho_setup_device;
static device_method_t psycho_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, psycho_probe),
DEVMETHOD(device_attach, psycho_attach),
DEVMETHOD(device_shutdown, bus_generic_shutdown),
DEVMETHOD(device_suspend, bus_generic_suspend),
DEVMETHOD(device_resume, bus_generic_resume),
/* Bus interface */
DEVMETHOD(bus_read_ivar, psycho_read_ivar),
DEVMETHOD(bus_setup_intr, psycho_setup_intr),
DEVMETHOD(bus_teardown_intr, bus_generic_teardown_intr),
DEVMETHOD(bus_alloc_resource, psycho_alloc_resource),
DEVMETHOD(bus_activate_resource, psycho_activate_resource),
DEVMETHOD(bus_deactivate_resource, bus_generic_deactivate_resource),
DEVMETHOD(bus_adjust_resource, psycho_adjust_resource),
DEVMETHOD(bus_release_resource, bus_generic_release_resource),
DEVMETHOD(bus_get_dma_tag, psycho_get_dma_tag),
/* pcib interface */
DEVMETHOD(pcib_maxslots, psycho_maxslots),
DEVMETHOD(pcib_read_config, psycho_read_config),
DEVMETHOD(pcib_write_config, psycho_write_config),
DEVMETHOD(pcib_route_interrupt, psycho_route_interrupt),
/* ofw_bus interface */
DEVMETHOD(ofw_bus_get_node, psycho_get_node),
/* ofw_pci interface */
DEVMETHOD(ofw_pci_setup_device, psycho_setup_device),
DEVMETHOD_END
};
static devclass_t psycho_devclass;
DEFINE_CLASS_0(pcib, psycho_driver, psycho_methods,
sizeof(struct psycho_softc));
EARLY_DRIVER_MODULE(psycho, nexus, psycho_driver, psycho_devclass, 0, 0,
BUS_PASS_BUS);
static SLIST_HEAD(, psycho_softc) psycho_softcs =
SLIST_HEAD_INITIALIZER(psycho_softcs);
static const struct intr_controller psycho_ic = {
psycho_intr_enable,
psycho_intr_disable,
psycho_intr_assign,
psycho_intr_clear
};
struct psycho_icarg {
struct psycho_softc *pica_sc;
bus_addr_t pica_map;
bus_addr_t pica_clr;
};
#define PSYCHO_READ8(sc, off) \
bus_read_8((sc)->sc_mem_res, (off))
#define PSYCHO_WRITE8(sc, off, v) \
bus_write_8((sc)->sc_mem_res, (off), (v))
#define PCICTL_READ8(sc, off) \
PSYCHO_READ8((sc), (sc)->sc_pcictl + (off))
#define PCICTL_WRITE8(sc, off, v) \
PSYCHO_WRITE8((sc), (sc)->sc_pcictl + (off), (v))
/*
* "Sabre" is the UltraSPARC IIi onboard UPA to PCI bridge. It manages a
* single PCI bus and does not have a streaming buffer. It often has an APB
* (advanced PCI bridge) connected to it, which was designed specifically for
* the IIi. The APB let's the IIi handle two independednt PCI buses, and
* appears as two "Simba"'s underneath the Sabre.
*
* "Hummingbird" is the UltraSPARC IIe onboard UPA to PCI bridge. It's
* basically the same as Sabre but without an APB underneath it.
*
* "Psycho" and "Psycho+" are dual UPA to PCI bridges. They sit on the UPA
* bus and manage two PCI buses. "Psycho" has two 64-bit 33MHz buses, while
* "Psycho+" controls both a 64-bit 33Mhz and a 64-bit 66Mhz PCI bus. You
* will usually find a "Psycho+" since I don't think the original "Psycho"
* ever shipped, and if it did it would be in the U30.
*
* Each "Psycho" PCI bus appears as a separate OFW node, but since they are
* both part of the same IC, they only have a single register space. As such,
* they need to be configured together, even though the autoconfiguration will
* attach them separately.
*
* On UltraIIi machines, "Sabre" itself usually takes pci0, with "Simba" often
* as pci1 and pci2, although they have been implemented with other PCI bus
* numbers on some machines.
*
* On UltraII machines, there can be any number of "Psycho+" ICs, each
* providing two PCI buses.
*/
struct psycho_desc {
const char *pd_string;
int pd_mode;
const char *pd_name;
};
static const struct psycho_desc const psycho_compats[] = {
{ "pci108e,8000", PSYCHO_MODE_PSYCHO, "Psycho compatible" },
{ "pci108e,a000", PSYCHO_MODE_SABRE, "Sabre compatible" },
{ "pci108e,a001", PSYCHO_MODE_SABRE, "Hummingbird compatible" },
{ NULL, 0, NULL }
};
static const struct psycho_desc const psycho_models[] = {
{ "SUNW,psycho", PSYCHO_MODE_PSYCHO, "Psycho" },
{ "SUNW,sabre", PSYCHO_MODE_SABRE, "Sabre" },
{ NULL, 0, NULL }
};
static const struct psycho_desc *
psycho_find_desc(const struct psycho_desc *table, const char *string)
{
const struct psycho_desc *desc;
if (string == NULL)
return (NULL);
for (desc = table; desc->pd_string != NULL; desc++)
if (strcmp(desc->pd_string, string) == 0)
return (desc);
return (NULL);
}
static const struct psycho_desc *
psycho_get_desc(device_t dev)
{
const struct psycho_desc *rv;
rv = psycho_find_desc(psycho_models, ofw_bus_get_model(dev));
if (rv == NULL)
rv = psycho_find_desc(psycho_compats,
ofw_bus_get_compat(dev));
return (rv);
}
static int
psycho_probe(device_t dev)
{
const char *dtype;
dtype = ofw_bus_get_type(dev);
if (dtype != NULL && strcmp(dtype, OFW_TYPE_PCI) == 0 &&
psycho_get_desc(dev) != NULL) {
device_set_desc(dev, "U2P UPA-PCI bridge");
return (0);
}
return (ENXIO);
}
static int
psycho_attach(device_t dev)
{
struct psycho_icarg *pica;
struct psycho_softc *asc, *sc, *osc;
struct ofw_pci_ranges *range;
const struct psycho_desc *desc;
bus_addr_t intrclr, intrmap;
uint64_t csr, dr;
phandle_t node;
uint32_t dvmabase, prop, prop_array[2];
u_int rerun, ver;
int i, j;
node = ofw_bus_get_node(dev);
sc = device_get_softc(dev);
desc = psycho_get_desc(dev);
sc->sc_node = node;
sc->sc_dev = dev;
sc->sc_mode = desc->pd_mode;
/*
* The Psycho gets three register banks:
* (0) per-PBM configuration and status registers
* (1) per-PBM PCI configuration space, containing only the
* PBM 256-byte PCI header
* (2) the shared Psycho configuration registers
*/
if (sc->sc_mode == PSYCHO_MODE_PSYCHO) {
i = 2;
sc->sc_pcictl =
bus_get_resource_start(dev, SYS_RES_MEMORY, 0) -
bus_get_resource_start(dev, SYS_RES_MEMORY, 2);
switch (sc->sc_pcictl) {
case PSR_PCICTL0:
sc->sc_half = 0;
break;
case PSR_PCICTL1:
sc->sc_half = 1;
break;
default:
panic("%s: bogus PCI control register location",
__func__);
/* NOTREACHED */
}
} else {
i = 0;
sc->sc_pcictl = PSR_PCICTL0;
sc->sc_half = 0;
}
sc->sc_mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &i,
(sc->sc_mode == PSYCHO_MODE_PSYCHO ? RF_SHAREABLE : 0) |
RF_ACTIVE);
if (sc->sc_mem_res == NULL)
panic("%s: could not allocate registers", __func__);
/*
* Match other Psychos that are already configured against
* the base physical address. This will be the same for a
* pair of devices that share register space.
*/
osc = NULL;
SLIST_FOREACH(asc, &psycho_softcs, sc_link) {
if (rman_get_start(asc->sc_mem_res) ==
rman_get_start(sc->sc_mem_res)) {
/* Found partner. */
osc = asc;
break;
}
}
if (osc == NULL) {
sc->sc_mtx = malloc(sizeof(*sc->sc_mtx), M_DEVBUF,
M_NOWAIT | M_ZERO);
if (sc->sc_mtx == NULL)
panic("%s: could not malloc mutex", __func__);
mtx_init(sc->sc_mtx, "pcib_mtx", NULL, MTX_SPIN);
} else {
if (sc->sc_mode != PSYCHO_MODE_PSYCHO)
panic("%s: no partner expected", __func__);
if (mtx_initialized(osc->sc_mtx) == 0)
panic("%s: mutex not initialized", __func__);
sc->sc_mtx = osc->sc_mtx;
}
csr = PSYCHO_READ8(sc, PSR_CS);
ver = PSYCHO_GCSR_VERS(csr);
sc->sc_ign = 0x1f; /* Hummingbird/Sabre IGN is always 0x1f. */
if (sc->sc_mode == PSYCHO_MODE_PSYCHO)
sc->sc_ign = PSYCHO_GCSR_IGN(csr);
if (OF_getprop(node, "clock-frequency", &prop, sizeof(prop)) == -1)
prop = 33000000;
device_printf(dev,
"%s, impl %d, version %d, IGN %#x, bus %c, %dMHz\n",
desc->pd_name, (u_int)PSYCHO_GCSR_IMPL(csr), ver, sc->sc_ign,
'A' + sc->sc_half, prop / 1000 / 1000);
/* Set up the PCI control and PCI diagnostic registers. */
csr = PCICTL_READ8(sc, PCR_CS);
csr &= ~PCICTL_ARB_PARK;
if (OF_getproplen(node, "no-bus-parking") < 0)
csr |= PCICTL_ARB_PARK;
/* Workarounds for version specific bugs. */
dr = PCICTL_READ8(sc, PCR_DIAG);
switch (ver) {
case 0:
dr |= DIAG_RTRY_DIS;
dr &= ~DIAG_DWSYNC_DIS;
rerun = 0;
break;
case 1:
csr &= ~PCICTL_ARB_PARK;
dr |= DIAG_RTRY_DIS | DIAG_DWSYNC_DIS;
rerun = 0;
break;
default:
dr |= DIAG_DWSYNC_DIS;
dr &= ~DIAG_RTRY_DIS;
rerun = 1;
break;
}
csr |= PCICTL_ERRINTEN | PCICTL_ARB_4;
csr &= ~(PCICTL_SBHINTEN | PCICTL_WAKEUPEN);
#ifdef PSYCHO_DEBUG
device_printf(dev, "PCI CSR 0x%016llx -> 0x%016llx\n",
(unsigned long long)PCICTL_READ8(sc, PCR_CS),
(unsigned long long)csr);
#endif
PCICTL_WRITE8(sc, PCR_CS, csr);
dr &= ~DIAG_ISYNC_DIS;
#ifdef PSYCHO_DEBUG
device_printf(dev, "PCI DR 0x%016llx -> 0x%016llx\n",
(unsigned long long)PCICTL_READ8(sc, PCR_DIAG),
(unsigned long long)dr);
#endif
PCICTL_WRITE8(sc, PCR_DIAG, dr);
if (sc->sc_mode == PSYCHO_MODE_SABRE) {
/* Use the PROM preset for now. */
csr = PCICTL_READ8(sc, PCR_TAS);
if (csr == 0)
panic("%s: Hummingbird/Sabre TAS not initialized.",
__func__);
dvmabase = (ffs(csr) - 1) << PCITAS_ADDR_SHIFT;
} else
dvmabase = -1;
/* Initialize memory and I/O rmans. */
sc->sc_pci_io_rman.rm_type = RMAN_ARRAY;
sc->sc_pci_io_rman.rm_descr = "Psycho PCI I/O Ports";
if (rman_init(&sc->sc_pci_io_rman) != 0 ||
rman_manage_region(&sc->sc_pci_io_rman, 0, PSYCHO_IO_SIZE) != 0)
panic("%s: failed to set up I/O rman", __func__);
sc->sc_pci_mem_rman.rm_type = RMAN_ARRAY;
sc->sc_pci_mem_rman.rm_descr = "Psycho PCI Memory";
if (rman_init(&sc->sc_pci_mem_rman) != 0 ||
rman_manage_region(&sc->sc_pci_mem_rman, 0, PSYCHO_MEM_SIZE) != 0)
panic("%s: failed to set up memory rman", __func__);
i = OF_getprop_alloc(node, "ranges", sizeof(*range), (void **)&range);
/*
* Make sure that the expected ranges are present. The
* OFW_PCI_CS_MEM64 one is not currently used though.
*/
if (i != PSYCHO_NRANGE)
panic("%s: unsupported number of ranges", __func__);
/*
* Find the addresses of the various bus spaces.
* There should not be multiple ones of one kind.
* The physical start addresses of the ranges are the configuration,
* memory and I/O handles.
*/
for (i = 0; i < PSYCHO_NRANGE; i++) {
j = OFW_PCI_RANGE_CS(&range[i]);
if (sc->sc_pci_bh[j] != 0)
panic("%s: duplicate range for space %d",
__func__, j);
sc->sc_pci_bh[j] = OFW_PCI_RANGE_PHYS(&range[i]);
}
free(range, M_OFWPROP);
/* Register the softc, this is needed for paired Psychos. */
SLIST_INSERT_HEAD(&psycho_softcs, sc, sc_link);
/*
* If we're a Hummingbird/Sabre or the first of a pair of Psychos
* to arrive here, do the interrupt setup and start up the IOMMU.
*/
if (osc == NULL) {
/*
* Hunt through all the interrupt mapping regs and register
* our interrupt controller for the corresponding interrupt
* vectors. We do this early in order to be able to catch
* stray interrupts.
*/
for (i = 0; i <= PSYCHO_MAX_INO; i++) {
if (psycho_find_intrmap(sc, i, &intrmap, &intrclr,
NULL) == 0)
continue;
pica = malloc(sizeof(*pica), M_DEVBUF, M_NOWAIT);
if (pica == NULL)
panic("%s: could not allocate interrupt "
"controller argument", __func__);
pica->pica_sc = sc;
pica->pica_map = intrmap;
pica->pica_clr = intrclr;
#ifdef PSYCHO_DEBUG
/*
* Enable all interrupts and clear all interrupt
* states. This aids the debugging of interrupt
* routing problems.
*/
device_printf(dev,
"intr map (INO %d, %s) %#lx: %#lx, clr: %#lx\n",
i, intrmap <= PSR_PCIB3_INT_MAP ? "PCI" : "OBIO",
(u_long)intrmap, (u_long)PSYCHO_READ8(sc,
intrmap), (u_long)intrclr);
PSYCHO_WRITE8(sc, intrmap, INTMAP_VEC(sc->sc_ign, i));
PSYCHO_WRITE8(sc, intrclr, INTCLR_IDLE);
PSYCHO_WRITE8(sc, intrmap,
INTMAP_ENABLE(INTMAP_VEC(sc->sc_ign, i),
PCPU_GET(mid)));
#endif
j = intr_controller_register(INTMAP_VEC(sc->sc_ign,
i), &psycho_ic, pica);
if (j != 0)
device_printf(dev, "could not register "
"interrupt controller for INO %d (%d)\n",
i, j);
}
if (sc->sc_mode == PSYCHO_MODE_PSYCHO)
sparc64_counter_init(device_get_nameunit(dev),
rman_get_bustag(sc->sc_mem_res),
rman_get_bushandle(sc->sc_mem_res), PSR_TC0);
/*
* Set up IOMMU and PCI configuration if we're the first
* of a pair of Psychos to arrive here or a Hummingbird
* or Sabre.
*
* We should calculate a TSB size based on amount of RAM
* and number of bus controllers and number and type of
* child devices.
*
* For the moment, 32KB should be more than enough.
*/
sc->sc_is = malloc(sizeof(*sc->sc_is), M_DEVBUF, M_NOWAIT |
M_ZERO);
if (sc->sc_is == NULL)
panic("%s: could not malloc IOMMU state", __func__);
sc->sc_is->is_flags = IOMMU_PRESERVE_PROM;
if (sc->sc_mode == PSYCHO_MODE_SABRE) {
sc->sc_dma_methods =
malloc(sizeof(*sc->sc_dma_methods), M_DEVBUF,
M_NOWAIT);
if (sc->sc_dma_methods == NULL)
panic("%s: could not malloc DMA methods",
__func__);
memcpy(sc->sc_dma_methods, &iommu_dma_methods,
sizeof(*sc->sc_dma_methods));
sc->sc_dma_methods->dm_dmamap_sync =
sabre_dmamap_sync;
sc->sc_is->is_pmaxaddr =
IOMMU_MAXADDR(SABRE_IOMMU_BITS);
} else {
sc->sc_dma_methods = &iommu_dma_methods;
sc->sc_is->is_pmaxaddr =
IOMMU_MAXADDR(PSYCHO_IOMMU_BITS);
}
sc->sc_is->is_sb[0] = sc->sc_is->is_sb[1] = 0;
if (OF_getproplen(node, "no-streaming-cache") < 0)
sc->sc_is->is_sb[0] = sc->sc_pcictl + PCR_STRBUF;
sc->sc_is->is_flags |= (rerun != 1) ? IOMMU_RERUN_DISABLE : 0;
psycho_iommu_init(sc, 3, dvmabase);
} else {
/* Just copy IOMMU state, config tag and address. */
sc->sc_dma_methods = &iommu_dma_methods;
sc->sc_is = osc->sc_is;
if (OF_getproplen(node, "no-streaming-cache") < 0)
sc->sc_is->is_sb[1] = sc->sc_pcictl + PCR_STRBUF;
iommu_reset(sc->sc_is);
}
/* Allocate our tags. */
sc->sc_pci_iot = sparc64_alloc_bus_tag(NULL, rman_get_bustag(
sc->sc_mem_res), PCI_IO_BUS_SPACE, NULL);
if (sc->sc_pci_iot == NULL)
panic("%s: could not allocate PCI I/O tag", __func__);
sc->sc_pci_cfgt = sparc64_alloc_bus_tag(NULL, rman_get_bustag(
sc->sc_mem_res), PCI_CONFIG_BUS_SPACE, NULL);
if (sc->sc_pci_cfgt == NULL)
panic("%s: could not allocate PCI configuration space tag",
__func__);
if (bus_dma_tag_create(bus_get_dma_tag(dev), 8, 0,
sc->sc_is->is_pmaxaddr, ~0, NULL, NULL, sc->sc_is->is_pmaxaddr,
0xff, 0xffffffff, 0, NULL, NULL, &sc->sc_pci_dmat) != 0)
panic("%s: could not create PCI DMA tag", __func__);
/* Customize the tag. */
sc->sc_pci_dmat->dt_cookie = sc->sc_is;
sc->sc_pci_dmat->dt_mt = sc->sc_dma_methods;
i = OF_getprop(node, "bus-range", (void *)prop_array,
sizeof(prop_array));
if (i == -1)
panic("%s: could not get bus-range", __func__);
if (i != sizeof(prop_array))
panic("%s: broken bus-range (%d)", __func__, i);
sc->sc_pci_secbus = prop_array[0];
sc->sc_pci_subbus = prop_array[1];
if (bootverbose)
device_printf(dev, "bus range %u to %u; PCI bus %d\n",
sc->sc_pci_secbus, sc->sc_pci_subbus, sc->sc_pci_secbus);
/* Clear any pending PCI error bits. */
PCIB_WRITE_CONFIG(dev, sc->sc_pci_secbus, PCS_DEVICE, PCS_FUNC,
PCIR_STATUS, PCIB_READ_CONFIG(dev, sc->sc_pci_secbus,
PCS_DEVICE, PCS_FUNC, PCIR_STATUS, 2), 2);
PCICTL_WRITE8(sc, PCR_CS, PCICTL_READ8(sc, PCR_CS));
PCICTL_WRITE8(sc, PCR_AFS, PCICTL_READ8(sc, PCR_AFS));
if (osc == NULL) {
/*
* Establish handlers for interesting interrupts...
*
* XXX We need to remember these and remove this to support
* hotplug on the UPA/FHC bus.
*
* XXX Not all controllers have these, but installing them
* is better than trying to sort through this mess.
*/
psycho_set_intr(sc, 1, PSR_UE_INT_MAP, psycho_ue, NULL);
psycho_set_intr(sc, 2, PSR_CE_INT_MAP, psycho_ce, NULL);
#ifdef DEBUGGER_ON_POWERFAIL
psycho_set_intr(sc, 3, PSR_POWER_INT_MAP, psycho_powerfail,
NULL);
#else
psycho_set_intr(sc, 3, PSR_POWER_INT_MAP, NULL,
(driver_intr_t *)psycho_powerfail);
#endif
if (sc->sc_mode == PSYCHO_MODE_PSYCHO) {
/*
* Hummingbirds/Sabres do not have the following two
* interrupts.
*/
/*
* The spare hardware interrupt is used for the
* over-temperature interrupt.
*/
psycho_set_intr(sc, 4, PSR_SPARE_INT_MAP,
NULL, psycho_overtemp);
#ifdef PSYCHO_MAP_WAKEUP
/*
* psycho_wakeup() doesn't do anything useful right
* now.
*/
psycho_set_intr(sc, 5, PSR_PWRMGT_INT_MAP,
psycho_wakeup, NULL);
#endif /* PSYCHO_MAP_WAKEUP */
}
}
/*
* Register a PCI bus error interrupt handler according to which
* half this is. Hummingbird/Sabre don't have a PCI bus B error
* interrupt but they are also only used for PCI bus A.
*/
psycho_set_intr(sc, 0, sc->sc_half == 0 ? PSR_PCIAERR_INT_MAP :
PSR_PCIBERR_INT_MAP, psycho_pci_bus, NULL);
/*
* Set the latency timer register as this isn't always done by the
* firmware.
*/
PCIB_WRITE_CONFIG(dev, sc->sc_pci_secbus, PCS_DEVICE, PCS_FUNC,
PCIR_LATTIMER, OFW_PCI_LATENCY, 1);
for (i = PCIR_VENDOR; i < PCIR_STATUS; i += sizeof(uint16_t))
le16enc(&sc->sc_pci_hpbcfg[i], bus_space_read_2(
sc->sc_pci_cfgt, sc->sc_pci_bh[OFW_PCI_CS_CONFIG],
PSYCHO_CONF_OFF(sc->sc_pci_secbus, PCS_DEVICE,
PCS_FUNC, i)));
for (i = PCIR_REVID; i <= PCIR_BIST; i += sizeof(uint8_t))
sc->sc_pci_hpbcfg[i] = bus_space_read_1(sc->sc_pci_cfgt,
sc->sc_pci_bh[OFW_PCI_CS_CONFIG], PSYCHO_CONF_OFF(
sc->sc_pci_secbus, PCS_DEVICE, PCS_FUNC, i));
ofw_bus_setup_iinfo(node, &sc->sc_pci_iinfo, sizeof(ofw_pci_intr_t));
/*
* On E250 the interrupt map entry for the EBus bridge is wrong,
* causing incorrect interrupts to be assigned to some devices on
* the EBus. Work around it by changing our copy of the interrupt
* map mask to perform a full comparison of the INO. That way
* the interrupt map entry for the EBus bridge won't match at all
* and the INOs specified in the "interrupts" properties of the
* EBus devices will be used directly instead.
*/
if (strcmp(sparc64_model, "SUNW,Ultra-250") == 0 &&
sc->sc_pci_iinfo.opi_imapmsk != NULL)
*(ofw_pci_intr_t *)(&sc->sc_pci_iinfo.opi_imapmsk[
sc->sc_pci_iinfo.opi_addrc]) = INTMAP_INO_MASK;
device_add_child(dev, "pci", -1);
return (bus_generic_attach(dev));
}
static void
psycho_set_intr(struct psycho_softc *sc, u_int index, bus_addr_t intrmap,
driver_filter_t filt, driver_intr_t intr)
{
u_long vec;
int rid;
rid = index;
sc->sc_irq_res[index] = bus_alloc_resource_any(sc->sc_dev,
SYS_RES_IRQ, &rid, RF_ACTIVE);
if (sc->sc_irq_res[index] == NULL && intrmap >= PSR_POWER_INT_MAP) {
/*
* These interrupts aren't mandatory and not available
* with all controllers (not even Psychos).
*/
return;
}
if (sc->sc_irq_res[index] == NULL ||
INTIGN(vec = rman_get_start(sc->sc_irq_res[index])) !=
sc->sc_ign ||
INTVEC(PSYCHO_READ8(sc, intrmap)) != vec ||
intr_vectors[vec].iv_ic != &psycho_ic ||
bus_setup_intr(sc->sc_dev, sc->sc_irq_res[index],
INTR_TYPE_MISC | INTR_BRIDGE, filt, intr, sc,
&sc->sc_ihand[index]) != 0)
panic("%s: failed to set up interrupt %d", __func__, index);
}
static int
psycho_find_intrmap(struct psycho_softc *sc, u_int ino,
bus_addr_t *intrmapptr, bus_addr_t *intrclrptr, bus_addr_t *intrdiagptr)
{
bus_addr_t intrclr, intrmap;
uint64_t diag;
int found;
/*
* XXX we only compare INOs rather than INRs since the firmware may
* not provide the IGN and the IGN is constant for all devices on
* that PCI controller.
* This could cause problems for the FFB/external interrupt which
* has a full vector that can be set arbitrarily.
*/
if (ino > PSYCHO_MAX_INO) {
device_printf(sc->sc_dev, "out of range INO %d requested\n",
ino);
return (0);
}
found = 0;
/* Hunt through OBIO first. */
diag = PSYCHO_READ8(sc, PSR_OBIO_INT_DIAG);
for (intrmap = PSR_SCSI_INT_MAP, intrclr = PSR_SCSI_INT_CLR;
intrmap <= PSR_PWRMGT_INT_MAP; intrmap += 8, intrclr += 8,
diag >>= 2) {
if (sc->sc_mode == PSYCHO_MODE_SABRE &&
(intrmap == PSR_TIMER0_INT_MAP ||
intrmap == PSR_TIMER1_INT_MAP ||
intrmap == PSR_PCIBERR_INT_MAP ||
intrmap == PSR_PWRMGT_INT_MAP))
continue;
if (INTINO(PSYCHO_READ8(sc, intrmap)) == ino) {
diag &= 2;
found = 1;
break;
}
}
if (!found) {
diag = PSYCHO_READ8(sc, PSR_PCI_INT_DIAG);
/* Now do PCI interrupts. */
for (intrmap = PSR_PCIA0_INT_MAP, intrclr = PSR_PCIA0_INT_CLR;
intrmap <= PSR_PCIB3_INT_MAP; intrmap += 8, intrclr += 32,
diag >>= 8) {
if (sc->sc_mode == PSYCHO_MODE_PSYCHO &&
(intrmap == PSR_PCIA2_INT_MAP ||
intrmap == PSR_PCIA3_INT_MAP))
continue;
if (((PSYCHO_READ8(sc, intrmap) ^ ino) & 0x3c) == 0) {
intrclr += 8 * (ino & 3);
diag = (diag >> ((ino & 3) * 2)) & 2;
found = 1;
break;
}
}
}
if (intrmapptr != NULL)
*intrmapptr = intrmap;
if (intrclrptr != NULL)
*intrclrptr = intrclr;
if (intrdiagptr != NULL)
*intrdiagptr = diag;
return (found);
}
/*
* Interrupt handlers
*/
static int
psycho_ue(void *arg)
{
struct psycho_softc *sc = arg;
uint64_t afar, afsr;
afar = PSYCHO_READ8(sc, PSR_UE_AFA);
afsr = PSYCHO_READ8(sc, PSR_UE_AFS);
/*
* On the UltraSPARC-IIi/IIe, IOMMU misses/protection faults cause
* the AFAR to be set to the physical address of the TTE entry that
* was invalid/write protected. Call into the IOMMU code to have
* them decoded to virtual I/O addresses.
*/
if ((afsr & UEAFSR_P_DTE) != 0)
iommu_decode_fault(sc->sc_is, afar);
panic("%s: uncorrectable DMA error AFAR %#lx AFSR %#lx",
device_get_nameunit(sc->sc_dev), (u_long)afar, (u_long)afsr);
return (FILTER_HANDLED);
}
static int
psycho_ce(void *arg)
{
struct psycho_softc *sc = arg;
uint64_t afar, afsr;
mtx_lock_spin(sc->sc_mtx);
afar = PSYCHO_READ8(sc, PSR_CE_AFA);
afsr = PSYCHO_READ8(sc, PSR_CE_AFS);
device_printf(sc->sc_dev, "correctable DMA error AFAR %#lx "
"AFSR %#lx\n", (u_long)afar, (u_long)afsr);
/* Clear the error bits that we caught. */
PSYCHO_WRITE8(sc, PSR_CE_AFS, afsr);
mtx_unlock_spin(sc->sc_mtx);
return (FILTER_HANDLED);
}
static int
psycho_pci_bus(void *arg)
{
struct psycho_softc *sc = arg;
uint64_t afar, afsr;
afar = PCICTL_READ8(sc, PCR_AFA);
afsr = PCICTL_READ8(sc, PCR_AFS);
panic("%s: PCI bus %c error AFAR %#lx AFSR %#lx",
device_get_nameunit(sc->sc_dev), 'A' + sc->sc_half, (u_long)afar,
(u_long)afsr);
return (FILTER_HANDLED);
}
static int
psycho_powerfail(void *arg)
{
#ifdef DEBUGGER_ON_POWERFAIL
struct psycho_softc *sc = arg;
kdb_enter(KDB_WHY_POWERFAIL, "powerfail");
#else
static int shutdown;
/* As the interrupt is cleared we may be called multiple times. */
if (shutdown != 0)
return (FILTER_HANDLED);
shutdown++;
printf("Power Failure Detected: Shutting down NOW.\n");
shutdown_nice(0);
#endif
return (FILTER_HANDLED);
}
static void
psycho_overtemp(void *arg)
{
static int shutdown;
/* As the interrupt is cleared we may be called multiple times. */
if (shutdown != 0)
return;
shutdown++;
printf("DANGER: OVER TEMPERATURE detected.\nShutting down NOW.\n");
shutdown_nice(RB_POWEROFF);
}
#ifdef PSYCHO_MAP_WAKEUP
static int
psycho_wakeup(void *arg)
{
struct psycho_softc *sc = arg;
/* We don't really have a framework to deal with this properly. */
device_printf(sc->sc_dev, "power management wakeup\n");
return (FILTER_HANDLED);
}
#endif /* PSYCHO_MAP_WAKEUP */
static void
psycho_iommu_init(struct psycho_softc *sc, int tsbsize, uint32_t dvmabase)
{
struct iommu_state *is = sc->sc_is;
/* Punch in our copies. */
is->is_bustag = rman_get_bustag(sc->sc_mem_res);
is->is_bushandle = rman_get_bushandle(sc->sc_mem_res);
is->is_iommu = PSR_IOMMU;
is->is_dtag = PSR_IOMMU_TLB_TAG_DIAG;
is->is_ddram = PSR_IOMMU_TLB_DATA_DIAG;
is->is_dqueue = PSR_IOMMU_QUEUE_DIAG;
is->is_dva = PSR_IOMMU_SVADIAG;
is->is_dtcmp = PSR_IOMMU_TLB_CMP_DIAG;
iommu_init(device_get_nameunit(sc->sc_dev), is, tsbsize, dvmabase, 0);
}
static int
psycho_maxslots(device_t dev)
{
/* XXX: is this correct? */
return (PCI_SLOTMAX);
}
static uint32_t
psycho_read_config(device_t dev, u_int bus, u_int slot, u_int func, u_int reg,
int width)
{
struct psycho_softc *sc;
bus_space_handle_t bh;
u_long offset = 0;
uint8_t byte;
uint16_t shrt;
uint32_t r, wrd;
int i;
sc = device_get_softc(dev);
if (bus < sc->sc_pci_secbus || bus > sc->sc_pci_subbus ||
slot > PCI_SLOTMAX || func > PCI_FUNCMAX || reg > PCI_REGMAX)
return (-1);
bh = sc->sc_pci_bh[OFW_PCI_CS_CONFIG];
/*
* The Hummingbird and Sabre bridges are picky in that they
* only allow their config space to be accessed using the
* "native" width of the respective register being accessed
* and return semi-random other content of their config space
* otherwise. Given that the PCI specs don't say anything
* about such a (unusual) limitation and lots of stuff expects
* to be able to access the contents of the config space at
* any width we allow just that. We do this by using a copy
* of the header of the bridge (the rest is all zero anyway)
* read during attach (expect for PCIR_STATUS) in order to
* simplify things.
* The Psycho bridges contain a dupe of their header at 0x80
* which we nullify that way also.
*/
if (bus == sc->sc_pci_secbus && slot == PCS_DEVICE &&
func == PCS_FUNC) {
if (offset % width != 0)
return (-1);
if (reg >= sizeof(sc->sc_pci_hpbcfg))
return (0);
if ((reg < PCIR_STATUS && reg + width > PCIR_STATUS) ||
reg == PCIR_STATUS || reg == PCIR_STATUS + 1)
le16enc(&sc->sc_pci_hpbcfg[PCIR_STATUS],
bus_space_read_2(sc->sc_pci_cfgt, bh,
PSYCHO_CONF_OFF(sc->sc_pci_secbus,
PCS_DEVICE, PCS_FUNC, PCIR_STATUS)));
switch (width) {
case 1:
return (sc->sc_pci_hpbcfg[reg]);
case 2:
return (le16dec(&sc->sc_pci_hpbcfg[reg]));
case 4:
return (le32dec(&sc->sc_pci_hpbcfg[reg]));
}
}
offset = PSYCHO_CONF_OFF(bus, slot, func, reg);
switch (width) {
case 1:
i = bus_space_peek_1(sc->sc_pci_cfgt, bh, offset, &byte);
r = byte;
break;
case 2:
i = bus_space_peek_2(sc->sc_pci_cfgt, bh, offset, &shrt);
r = shrt;
break;
case 4:
i = bus_space_peek_4(sc->sc_pci_cfgt, bh, offset, &wrd);
r = wrd;
break;
default:
panic("%s: bad width", __func__);
/* NOTREACHED */
}
if (i) {
#ifdef PSYCHO_DEBUG
printf("%s: read data error reading: %d.%d.%d: 0x%x\n",
__func__, bus, slot, func, reg);
#endif
r = -1;
}
return (r);
}
static void
psycho_write_config(device_t dev, u_int bus, u_int slot, u_int func,
u_int reg, uint32_t val, int width)
{
struct psycho_softc *sc;
bus_space_handle_t bh;
u_long offset = 0;
sc = device_get_softc(dev);
if (bus < sc->sc_pci_secbus || bus > sc->sc_pci_subbus ||
slot > PCI_SLOTMAX || func > PCI_FUNCMAX || reg > PCI_REGMAX)
return;
offset = PSYCHO_CONF_OFF(bus, slot, func, reg);
bh = sc->sc_pci_bh[OFW_PCI_CS_CONFIG];
switch (width) {
case 1:
bus_space_write_1(sc->sc_pci_cfgt, bh, offset, val);
break;
case 2:
bus_space_write_2(sc->sc_pci_cfgt, bh, offset, val);
break;
case 4:
bus_space_write_4(sc->sc_pci_cfgt, bh, offset, val);
break;
default:
panic("%s: bad width", __func__);
/* NOTREACHED */
}
}
static int
psycho_route_interrupt(device_t bridge, device_t dev, int pin)
{
struct psycho_softc *sc;
struct ofw_pci_register reg;
bus_addr_t intrmap;
ofw_pci_intr_t pintr, mintr;
uint8_t maskbuf[sizeof(reg) + sizeof(pintr)];
sc = device_get_softc(bridge);
pintr = pin;
if (ofw_bus_lookup_imap(ofw_bus_get_node(dev), &sc->sc_pci_iinfo,
®, sizeof(reg), &pintr, sizeof(pintr), &mintr, sizeof(mintr),
NULL, maskbuf))
return (mintr);
/*
* If this is outside of the range for an intpin, it's likely a full
* INO, and no mapping is required at all; this happens on the U30,
* where there's no interrupt map at the Psycho node. Fortunately,
* there seem to be no INOs in the intpin range on this boxen, so
* this easy heuristics will do.
*/
if (pin > 4)
return (pin);
/*
* Guess the INO; we always assume that this is a non-OBIO
* device, and that pin is a "real" intpin number. Determine
* the mapping register to be used by the slot number.
* We only need to do this on E450s, it seems; here, the slot numbers
* for bus A are one-based, while those for bus B seemingly have an
* offset of 2 (hence the factor of 3 below).
*/
intrmap = PSR_PCIA0_INT_MAP +
8 * (pci_get_slot(dev) - 1 + 3 * sc->sc_half);
mintr = INTINO(PSYCHO_READ8(sc, intrmap)) + pin - 1;
device_printf(bridge,
"guessing interrupt %d for device %d.%d pin %d\n",
(int)mintr, pci_get_slot(dev), pci_get_function(dev), pin);
return (mintr);
}
static int
psycho_read_ivar(device_t dev, device_t child, int which, uintptr_t *result)
{
struct psycho_softc *sc;
sc = device_get_softc(dev);
switch (which) {
case PCIB_IVAR_DOMAIN:
*result = device_get_unit(dev);
return (0);
case PCIB_IVAR_BUS:
*result = sc->sc_pci_secbus;
return (0);
}
return (ENOENT);
}
static void
sabre_dmamap_sync(bus_dma_tag_t dt, bus_dmamap_t map, bus_dmasync_op_t op)
{
struct iommu_state *is = dt->dt_cookie;
if ((map->dm_flags & DMF_LOADED) == 0)
return;
if ((op & BUS_DMASYNC_POSTREAD) != 0)
(void)bus_space_read_8(is->is_bustag, is->is_bushandle,
PSR_DMA_WRITE_SYNC);
if ((op & BUS_DMASYNC_PREWRITE) != 0)
membar(Sync);
}
static void
psycho_intr_enable(void *arg)
{
struct intr_vector *iv = arg;
struct psycho_icarg *pica = iv->iv_icarg;
PSYCHO_WRITE8(pica->pica_sc, pica->pica_map,
INTMAP_ENABLE(iv->iv_vec, iv->iv_mid));
}
static void
psycho_intr_disable(void *arg)
{
struct intr_vector *iv = arg;
struct psycho_icarg *pica = iv->iv_icarg;
PSYCHO_WRITE8(pica->pica_sc, pica->pica_map, iv->iv_vec);
}
static void
psycho_intr_assign(void *arg)
{
struct intr_vector *iv = arg;
struct psycho_icarg *pica = iv->iv_icarg;
PSYCHO_WRITE8(pica->pica_sc, pica->pica_map, INTMAP_TID(
PSYCHO_READ8(pica->pica_sc, pica->pica_map), iv->iv_mid));
}
static void
psycho_intr_clear(void *arg)
{
struct intr_vector *iv = arg;
struct psycho_icarg *pica = iv->iv_icarg;
PSYCHO_WRITE8(pica->pica_sc, pica->pica_clr, INTCLR_IDLE);
}
static int
psycho_setup_intr(device_t dev, device_t child, struct resource *ires,
int flags, driver_filter_t *filt, driver_intr_t *intr, void *arg,
void **cookiep)
{
struct psycho_softc *sc;
u_long vec;
sc = device_get_softc(dev);
/*
* Make sure the vector is fully specified and we registered
* our interrupt controller for it.
*/
vec = rman_get_start(ires);
if (INTIGN(vec) != sc->sc_ign ||
intr_vectors[vec].iv_ic != &psycho_ic) {
device_printf(dev, "invalid interrupt vector 0x%lx\n", vec);
return (EINVAL);
}
return (bus_generic_setup_intr(dev, child, ires, flags, filt, intr,
arg, cookiep));
}
static struct resource *
psycho_alloc_resource(device_t bus, device_t child, int type, int *rid,
u_long start, u_long end, u_long count, u_int flags)
{
struct psycho_softc *sc;
struct resource *rv;
struct rman *rm;
sc = device_get_softc(bus);
switch (type) {
case SYS_RES_IRQ:
/*
* XXX: Don't accept blank ranges for now, only single
* interrupts. The other case should not happen with
* the MI PCI code...
* XXX: This may return a resource that is out of the
* range that was specified. Is this correct...?
*/
if (start != end)
panic("%s: XXX: interrupt range", __func__);
start = end = INTMAP_VEC(sc->sc_ign, end);
return (bus_generic_alloc_resource(bus, child, type, rid,
start, end, count, flags));
case SYS_RES_MEMORY:
rm = &sc->sc_pci_mem_rman;
break;
case SYS_RES_IOPORT:
rm = &sc->sc_pci_io_rman;
break;
default:
return (NULL);
}
rv = rman_reserve_resource(rm, start, end, count, flags & ~RF_ACTIVE,
child);
if (rv == NULL)
return (NULL);
rman_set_rid(rv, *rid);
if ((flags & RF_ACTIVE) != 0 && bus_activate_resource(child, type,
*rid, rv) != 0) {
rman_release_resource(rv);
return (NULL);
}
return (rv);
}
static int
psycho_activate_resource(device_t bus, device_t child, int type, int rid,
struct resource *r)
{
struct psycho_softc *sc;
struct bus_space_tag *tag;
sc = device_get_softc(bus);
switch (type) {
case SYS_RES_IRQ:
return (bus_generic_activate_resource(bus, child, type, rid,
r));
case SYS_RES_MEMORY:
tag = sparc64_alloc_bus_tag(r, rman_get_bustag(
sc->sc_mem_res), PCI_MEMORY_BUS_SPACE, NULL);
if (tag == NULL)
return (ENOMEM);
rman_set_bustag(r, tag);
rman_set_bushandle(r, sc->sc_pci_bh[OFW_PCI_CS_MEM32] +
rman_get_start(r));
break;
case SYS_RES_IOPORT:
rman_set_bustag(r, sc->sc_pci_iot);
rman_set_bushandle(r, sc->sc_pci_bh[OFW_PCI_CS_IO] +
rman_get_start(r));
break;
}
return (rman_activate_resource(r));
}
static int
psycho_adjust_resource(device_t bus, device_t child, int type,
struct resource *r, u_long start, u_long end)
{
struct psycho_softc *sc;
struct rman *rm;
sc = device_get_softc(bus);
switch (type) {
case SYS_RES_IRQ:
return (bus_generic_adjust_resource(bus, child, type, r,
start, end));
case SYS_RES_MEMORY:
rm = &sc->sc_pci_mem_rman;
break;
case SYS_RES_IOPORT:
rm = &sc->sc_pci_io_rman;
break;
default:
return (EINVAL);
}
if (rman_is_region_manager(r, rm) == 0)
return (EINVAL);
return (rman_adjust_resource(r, start, end));
}
static bus_dma_tag_t
psycho_get_dma_tag(device_t bus, device_t child __unused)
{
struct psycho_softc *sc;
sc = device_get_softc(bus);
return (sc->sc_pci_dmat);
}
static phandle_t
psycho_get_node(device_t bus, device_t child __unused)
{
struct psycho_softc *sc;
sc = device_get_softc(bus);
/* We only have one child, the PCI bus, which needs our own node. */
return (sc->sc_node);
}
static void
psycho_setup_device(device_t bus, device_t child)
{
struct psycho_softc *sc;
uint32_t rev;
sc = device_get_softc(bus);
/*
* Revision 0 EBus bridges have a bug which prevents them from
* working when bus parking is enabled.
*/
if ((strcmp(ofw_bus_get_name(child), "ebus") == 0 ||
strcmp(ofw_bus_get_name(child), "pci108e,1000") == 0) &&
OF_getprop(ofw_bus_get_node(child), "revision-id", &rev,
sizeof(rev)) > 0 && rev == 0)
PCICTL_WRITE8(sc, PCR_CS, PCICTL_READ8(sc, PCR_CS) &
~PCICTL_ARB_PARK);
}