| Current Path : /usr/src/usr.bin/mt/ |
FreeBSD hs32.drive.ne.jp 9.1-RELEASE FreeBSD 9.1-RELEASE #1: Wed Jan 14 12:18:08 JST 2015 root@hs32.drive.ne.jp:/sys/amd64/compile/hs32 amd64 |
| Current File : //usr/src/usr.bin/mt/mt.1 |
.\" Copyright (c) 1981, 1990, 1993
.\" The Regents of the University of California. All rights reserved.
.\"
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\" notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\" notice, this list of conditions and the following disclaimer in the
.\" documentation and/or other materials provided with the distribution.
.\" 4. Neither the name of the University nor the names of its contributors
.\" may be used to endorse or promote products derived from this software
.\" without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\" @(#)mt.1 8.1 (Berkeley) 6/6/93
.\" $FreeBSD: release/9.1.0/usr.bin/mt/mt.1 216370 2010-12-11 08:32:16Z joel $
.\"
.Dd January 20, 2008
.Dt MT 1
.Os
.Sh NAME
.Nm mt
.Nd magnetic tape manipulating program
.Sh SYNOPSIS
.Nm
.Op Fl f Ar tapename
.Ar command
.Op Ar count
.Nm
.Op Fl f Ar tapename
.Ar command
.Ar argument
.Sh DESCRIPTION
The
.Nm
utility is used to command a magnetic tape drive for operations
other than reading or writing data.
.Pp
The
.Fl f
option's
.Ar tapename
overrides the
.Ev TAPE
environment variable described below.
.Pp
The available commands are listed below.
Only as many
characters as are required to uniquely identify a command
need be specified.
.Pp
The following commands optionally take a
.Ar count ,
which defaults to 1.
.Bl -tag -width ".Cm erase"
.It Cm weof
Write
.Ar count
end-of-file (EOF) marks at the current position.
.It Cm smk
Write
.Ar count
setmarks at the current position (DDS drives only).
.It Cm fsf
Forward space
.Ar count
files.
.It Cm fsr
Forward space
.Ar count
records.
.It Cm fss
Forward space
.Ar count
setmarks (DDS drives only).
.It Cm bsf
Backward space
.Ar count
files.
.It Cm bsr
Backward space
.Ar count
records.
.It Cm bss
Backward space
.Ar count
setmarks (DDS drives only).
.It Cm erase
Erase the tape using a long (often very long) method.
With a
.Ar count
of 0, it will erase the tape using a quick method.
Operation is not guaranteed if the tape is not at its beginning.
The tape will be at its beginning upon completion.
.El
.Pp
The following commands ignore
.Ar count .
.Bl -tag -width ".Cm geteotmodel"
.It Cm rdhpos
Read the hardware block position.
The block
number reported is specific for that hardware only.
With drive data compression especially,
this position may have more to do with the amount of data
sent to the drive than the amount of data written to tape.
Some drives do not support this.
.It Cm rdspos
Read the SCSI logical block position.
This typically is greater than the hardware position
by the number of end-of-file marks.
Some drives do not support this.
.It Cm rewind
Rewind the tape.
.It Cm offline , rewoffl
Rewind the tape and place the drive off line.
Some drives are never off line.
.It Cm retension
Re-tension the tape.
This winds the tape from the current position to the end
and then to the beginning.
This sometimes improves subsequent reading and writing,
particularly for streaming drives.
Some drives do not support this.
.It Cm status
Output status information about the drive.
For SCSI magnetic tape devices,
the current operating modes of density, blocksize, and whether compression
is enabled is reported.
The current state of the driver (what it thinks that
it is doing with the device) is reported.
If the driver knows the relative
position from BOT (in terms of filemarks and records), it outputs that.
Note
that this information is not definitive (only BOT, End of Recorded Media, and
hardware or SCSI logical block position (if the drive supports such) are
considered definitive tape positions).
.It Cm errstat
Output (and clear) error status information about this device.
For every normal
operation (e.g., a read or a write) and every control operation (e.g,, a
rewind), the driver stores up the last command executed and it is associated
status and any residual counts (if any).
This command retrieves and outputs this
information.
If possible, this also clears any latched error information.
.It Cm geteotmodel
Output the current EOT filemark model.
The model states how
many filemarks will be written at close if a tape was being written.
.It Cm eod , eom
Wind the tape to the end of the recorded data,
typically after an EOF mark where another file may be written.
.El
.Pp
The following commands require an
.Ar argument .
.Bl -tag -width ".Cm seteotmodel"
.It Cm sethpos
Set the hardware block position.
The
.Ar argument
is a hardware block number to which to position the tape.
Some drives do not support this.
.It Cm setspos
Set the SCSI logical block position.
The
.Ar argument
is a SCSI logical block number to which to position the tape.
Some drives do not support this.
.It Cm blocksize
Set the block size for the drive.
The
.Ar argument
is the number of bytes per block,
except 0 commands the drive to use variable-length blocks.
.It Cm seteotmodel
Set the EOT filemark model to
.Ar argument
and output the old and new models.
Typically this will be 2
filemarks, but some devices (typically QIC cartridge drives) can
only write 1 filemark.
You may only choose a value of
.Ar 1
or
.Ar 2 .
.It Cm comp
Set the drive's compression mode.
The non-numeric values of
.Ar argument
are:
.Pp
.Bl -tag -width 9n -compact
.It off
Turn compression off.
.It on
Turn compression on.
.It none
Same as
.Ar off .
.It enable
Same as
.Ar on .
.It IDRC
IBM Improved Data Recording Capability compression (0x10).
.It DCLZ
DCLZ compression algorithm (0x20).
.El
.Pp
In addition to the above recognized compression keywords, the user can
supply a numeric compression algorithm for the drive to use.
In most
cases, simply turning the compression
.Sq on
will have the desired effect of enabling the default compression algorithm
supported by the drive.
If this is not the case (see the
.Cm status
display to see which compression algorithm is currently in use), the user
can manually specify one of the supported compression keywords (above), or
supply a numeric compression value from the drive's specifications.
.It Cm density
Set the density for the drive.
For the density codes, see below.
The density value could be given either numerically, or as a string,
corresponding to the
.Dq Reference
field.
If the string is abbreviated, it will be resolved in the order
shown in the table, and the first matching entry will be used.
If the
given string and the resulting canonical density name do not match
exactly, an informational message is output about what the given
string has been taken for.
.El
.Pp
The following density table was taken from the
.Sq Historical sequential access density codes
table (A-1) in Revision 11 of the SCSI-3 Stream Device Commands (SSC)
working draft, dated November 11, 1997.
.Pp
The density codes are:
.Bd -literal -offset 3n
0x0 default for device
0xE reserved for ECMA
Value Width Tracks Density Code Type Reference Note
mm in bpmm bpi
0x01 12.7 (0.5) 9 32 (800) NRZI R X3.22-1983 2
0x02 12.7 (0.5) 9 63 (1,600) PE R X3.39-1986 2
0x03 12.7 (0.5) 9 246 (6,250) GCR R X3.54-1986 2
0x05 6.3 (0.25) 4/9 315 (8,000) GCR C X3.136-1986 1
0x06 12.7 (0.5) 9 126 (3,200) PE R X3.157-1987 2
0x07 6.3 (0.25) 4 252 (6,400) IMFM C X3.116-1986 1
0x08 3.81 (0.15) 4 315 (8,000) GCR CS X3.158-1987 1
0x09 12.7 (0.5) 18 1,491 (37,871) GCR C X3.180 2
0x0A 12.7 (0.5) 22 262 (6,667) MFM C X3B5/86-199 1
0x0B 6.3 (0.25) 4 63 (1,600) PE C X3.56-1986 1
0x0C 12.7 (0.5) 24 500 (12,690) GCR C HI-TC1 1,6
0x0D 12.7 (0.5) 24 999 (25,380) GCR C HI-TC2 1,6
0x0F 6.3 (0.25) 15 394 (10,000) GCR C QIC-120 1,6
0x10 6.3 (0.25) 18 394 (10,000) GCR C QIC-150 1,6
0x11 6.3 (0.25) 26 630 (16,000) GCR C QIC-320 1,6
0x12 6.3 (0.25) 30 2,034 (51,667) RLL C QIC-1350 1,6
0x13 3.81 (0.15) 1 2,400 (61,000) DDS CS X3B5/88-185A 5
0x14 8.0 (0.315) 1 1,703 (43,245) RLL CS X3.202-1991 5
0x15 8.0 (0.315) 1 1,789 (45,434) RLL CS ECMA TC17 5
0x16 12.7 (0.5) 48 394 (10,000) MFM C X3.193-1990 1
0x17 12.7 (0.5) 48 1,673 (42,500) MFM C X3B5/91-174 1
0x18 12.7 (0.5) 112 1,673 (42,500) MFM C X3B5/92-50 1
0x19 12.7 (0.5) 128 2,460 (62,500) RLL C DLTapeIII 6,7
0x1A 12.7 (0.5) 128 3,214 (81,633) RLL C DLTapeIV(20) 6,7
0x1B 12.7 (0.5) 208 3,383 (85,937) RLL C DLTapeIV(35) 6,7
0x1C 6.3 (0.25) 34 1,654 (42,000) MFM C QIC-385M 1,6
0x1D 6.3 (0.25) 32 1,512 (38,400) GCR C QIC-410M 1,6
0x1E 6.3 (0.25) 30 1,385 (36,000) GCR C QIC-1000C 1,6
0x1F 6.3 (0.25) 30 2,666 (67,733) RLL C QIC-2100C 1,6
0x20 6.3 (0.25) 144 2,666 (67,733) RLL C QIC-6GB(M) 1,6
0x21 6.3 (0.25) 144 2,666 (67,733) RLL C QIC-20GB(C) 1,6
0x22 6.3 (0.25) 42 1,600 (40,640) GCR C QIC-2GB(C) ?
0x23 6.3 (0.25) 38 2,666 (67,733) RLL C QIC-875M ?
0x24 3.81 (0.15) 1 2,400 (61,000) CS DDS-2 5
0x25 3.81 (0.15) 1 3,816 (97,000) CS DDS-3 5
0x26 3.81 (0.15) 1 3,816 (97,000) CS DDS-4 5
0x27 8.0 (0.315) 1 3,056 (77,611) RLL CS Mammoth 5
0x28 12.7 (0.5) 36 1,491 (37,871) GCR C X3.224 1
0x29 12.7 (0.5)
0x2A
0x2B 12.7 (0.5) 3 ? ? ? C X3.267 5
0x41 12.7 (0.5) 208 3,868 (98,250) RLL C DLTapeIV(40) 6,7
0x48 12.7 (0.5) 448 5,236 (133,000) PRML C SDLTapeI(110) 6,8
0x49 12.7 (0.5) 448 7,598 (193,000) PRML C SDLTapeI(160) 6,8
.Ed
.Bd -literal -offset 3n
Code Description Type Description
---- -------------------------------------- ---- -----------
NRZI Non return to zero, change on ones R Reel-to-reel
GCR Group code recording C Cartridge
PE Phase encoded CS Cassette
IMFM Inverted modified frequency modulation
MFM Modified frequency modulation
DDS DAT data storage
RLL Run length limited
PRML Partial Response Maximum Likelihood
.Ed
.Bd -literal -offset 3n
NOTES
1. Serial recorded.
2. Parallel recorded.
3. Old format known as QIC-11.
5. Helical scan.
6. This is not an American National Standard. The reference is based on
an industry standard definition of the media format.
7. DLT recording: serially recorded track pairs (DLTapeIII and
DLTapeIV(20)), or track quads (DLTapeIV(35) and DLTapeIV(40)).
8. Super DLT (SDLT) recording: 56 serially recorded logical tracks with
8 physical tracks each.
.Ed
.Sh ENVIRONMENT
.Bl -tag -width ".Ev TAPE"
.It Ev TAPE
This is the pathname of the tape drive.
The default (if the variable is unset, but not if it is null) is
.Pa /dev/nsa0 .
It may be overridden with the
.Fl f
option.
.El
.Sh FILES
.Bl -tag -width ".Pa /dev/*sa[0-9]*" -compact
.It Pa /dev/*wt*
QIC-02/QIC-36 magnetic tape interface
.It Pa /dev/*sa[0-9]*
SCSI magnetic tape interface
.El
.Sh DIAGNOSTICS
The exit status will be 0 when the drive operations were successful,
2 when the drive operations were unsuccessful, and 1 for other
problems like an unrecognized command or a missing drive device.
.Sh COMPATIBILITY
Some undocumented commands support old software.
.Sh SEE ALSO
.Xr dd 1 ,
.Xr ioctl 2 ,
.Xr ast 4 ,
.Xr mtio 4 ,
.Xr sa 4 ,
.Xr environ 7
.Sh HISTORY
The
.Nm
command appeared in
.Bx 4.3 .
.Pp
Extensions regarding the
.Xr st 4
driver appeared in
.Bx 386 0.1
as a separate
.Nm st
command, and have been merged into the
.Nm
command in
.Fx 2.1 .
.Pp
The former
.Cm eof
command that used to be a synonym for
.Cm weof
has been abandoned in
.Fx 2.1
since it was often confused with
.Cm eom ,
which is fairly dangerous.
.Sh BUGS
The utility cannot be interrupted or killed during a long erase
(which can be longer than an hour), and it is easy to forget
that the default erase is long.
.Pp
Hardware block numbers do not always correspond to blocks on the tape
when the drive uses internal compression.
.Pp
Erasure is not guaranteed if the tape is not at its beginning.
.Pp
Tape-related documentation is poor, here and elsewhere.